Logiq-e-Service-Manual

[Page 1] GE Healthcare LOGIQ e/LOGIQ e Vet/LOGIQ i/ Basic Service Manual Part Number: 5370626-100 Revision: 7

[Page 2]

[Page 3] Important Precautions THIS SERVICE MANUAL IS AVAILABLE IN ENGLISH ONLY. • IF A CUSTOMER’S SERVICE PROVIDER REQUIRES A LANGUAGE OTHER THAN ENGLISH, IT IS THE CUSTOMER’S RESPONSIBILITY TO PROVIDE TRANSLATION SERVICES. WARNING • DO NOT ATTEMPT TO SERVICE THE EQUIPMENT UNLESS THIS SERVICE (EN) MANUAL HAS BEEN CONSULTED AND IS UNDERSTOOD. • FAILURE TO HEED THIS WARNING MAY RESULT IN INJURY TO THE SERVICE PROVIDER, OPERATOR OR PATIENT FROM ELECTRIC SHOCK, MECHANICAL OR OTHER HAZARDS. CE MANUEL DE MAINTENANCE N’EST DISPONIBLE QU’EN ANGLAIS. • SI LE TECHNICIEN DU CLIENT A BESOIN DE CE MANUEL DANS UNE AUTRE LANGUE QUE L’ANGLAIS, C’EST AU CLIENT QU’IL INCOMBE DE LE FAIRE TRADUIRE. AVERTISSEMENT • NE PAS TENTER D’INTERVENTION SUR LES é QUIPEMENTS TANT QUE LE (FR) MANUEL SERVICE N’A PAS é Té CONSULTé ET COMPRIS. • LE NON-RESPECT DE CET AVERTISSEMENT PEUT ENTRAîNER CHEZ LE TECHNICIEN, L’OPé RATEUR OU LE PATIENT DES BLESSURES DUES à DES DANGERS é LECTRIQUES, Mé CANIQUES OU AUTRES. DIESES KUNDENDIENST-HANDBUCH EXISTIERT NUR IN ENGLISCHER SPRACHE. • FALLS EIN FREMDER KUNDENDIENST EINE ANDERE SPRACHE BENö TIGT, IST ES AUFGABE DES KUNDEN Fü R EINE ENTSPRECHENDE ÜBERSETZUNG ZU SORGEN. • VERSUCHEN SIE NICHT, DAS GERä T ZU REPARIEREN, BEVOR DIESES WARNUNG (DE) KUNDENDIENST-HANDBUCH NICHT ZU RATE GEZOGEN UND VERSTANDEN WURDE. • WIRD DIESE WARNUNG NICHT BEACHTET, SO KANN ES ZU VERLETZUNGEN DES KUNDENDIENSTTECHNIKERS, DES BEDIENERS ODER DES PATIENTEN DURCH ELEKTRISCHE SCHLä GE, MECHANISCHE ODER SONSTIGE GEFAHREN KOMMEN. - i

[Page 4] ESTE MANUAL DE SERVICIO Só LO EXISTE EN INGLé S. • SI ALGú N PROVEEDOR DE SERVICIOS AJENO A GEHC SOLICITA UN IDIOMA QUE NO SEA EL INGLé S, ES RESPONSABILIDAD DEL CLIENTE OFRECER UN SERVICIO DE TRADUCCIó N. AVISO • NO SE DEBERá DAR SERVICIO Té CNICO AL EQUIPO, SIN HABER (ES) CONSULTADO Y COMPRENDIDO ESTE MANUAL DE SERVICIO. • LA NO OBSERVANCIA DEL PRESENTE AVISO PUEDE DAR LUGAR A QUE EL PROVEEDOR DE SERVICIOS, EL OPERADOR O EL PACIENTE SUFRAN LESIONES PROVOCADAS POR CAUSAS ELé CTRICAS, MECá NICAS O DE OTRA NATURALEZA. ESTE MANUAL DE ASSISTê NCIA Té CNICA Só SE ENCONTRA DISPONíVEL EM INGLê S. • SE QUALQUER OUTRO SERVIç O DE ASSISTê NCIA Té CNICA, QUE Nã O A GEHC, SOLICITAR ESTES MANUAIS NOUTRO IDIOMA, é DA RESPONSABILIDADE DO CLIENTE FORNECER OS SERVIç OS DE TRADUç ã O. ATENÇÃO (PT-Br) • Nã O TENTE REPARAR O EQUIPAMENTO SEM TER CONSULTADO E COMPREENDIDO ESTE MANUAL DE ASSISTê NCIA Té CNICA. • O Nã O CUMPRIMENTO DESTE AVISO PODE POR EM PERIGO A SEGURANç A DO Té CNICO, OPERADOR OU PACIENTE DEVIDO A‘ CHOQUES ELé TRICOS, MECâ NICOS OU OUTROS. ESTE MANUAL DE ASSISTÊNCIA ESTÁ DISPONÍVEL APENAS EM INGLÊS. • SE QUALQUER OUTRO SERVIÇO DE ASSISTÊNCIA TÉCNICA, QUE NÃO A GEHC, SOLICITAR ESTES MANUAIS NOUTRO IDIOMA, É DA RESPONSABILIDADE DO CLIENTE FORNECER OS SERVIÇOS DE TRADUÇÃO. • NÃO TENTE EFECTUAR REPARAÇÕES NO EQUIPAMENTO SEM TER AVISO (PT-pt) CONSULTADO E COMPREENDIDO PREVIAMENTE ESTE MANUAL. • A INOBSERVÂNCIA DESTE AVISO PODE RESULTAR EM FERIMENTOS NO TÉCNICO DE ASSISTÊNCIA, OPERADOR OU PACIENTE EM CONSEQUÊNCIA DE CHOQUE ELÉCTRICO, PERIGOS DE ORIGEM MECÂNICA, BEM COMO DE OUTROS TIPOS. IL PRESENTE MANUALE DI MANUTENZIONE è DISPONIBILE SOLTANTO IN INGLESE. • SE UN ADDETTO ALLA MANUTENZIONE ESTERNO ALLA GEHC RICHIEDE IL MANUALE IN UNA LINGUA DIVERSA, IL CLIENTE è TENUTO A PROVVEDERE DIRETTAMENTE ALLA TRADUZIONE. AVVERTENZA • SI PROCEDA ALLA MANUTENZIONE DELL’APPARECCHIATURA SOLO DOPO (IT) AVER CONSULTATO IL PRESENTE MANUALE ED AVERNE COMPRESO IL CONTENUTO. • NON TENERE CONTO DELLA PRESENTE AVVERTENZA POTREBBE FAR COMPIERE OPERAZIONI DA CUI DERIVINO LESIONI ALL’ADDETTO ALLA MANUTENZIONE, ALL’UTILIZZATORE ED AL PAZIENTE PER FOLGORAZIONE ELETTRICA, PER URTI MECCANICI OD ALTRI RISCHI. ii -

[Page 5] KÄESOLEV TEENINDUSJUHEND ON SAADAVAL AINULT INGLISE KEELES. • KUI KLIENDITEENINDUSE OSUTAJA Nõ UAB JUHENDIT INGLISE KEELEST ERINEVAS KEELES, VASTUTAB KLIENT Tõ LKETEENUSE OSUTAMISE EEST. HOIATUS • ä RGE ü RITAGE SEADMEID TEENINDADA ENNE EELNEVALT Kä ESOLEVA (ET) TEENINDUSJUHENDIGA TUTVUMIST JA SELLEST ARU SAAMIST. • Kä ESOLEVA HOIATUSE EIRAMINE Võ IB Põ HJUSTADA TEENUSEOSUTAJA, OPERAATORI Võ I PATSIENDI VIGASTAMIST ELEKTRILö ö GI, MEHAANILISE Võ I MUU OHU TAGAJä RJEL. TÄMÄ HUOLTO-OHJE ON SAATAVILLA VAIN ENGLANNIKSI. • JOS ASIAKKAAN PALVELUNTARJOAJA VAATII MUUTA KUIN ENGLANNINKIELISTä MATERIAALIA, TARVITTAVAN Kä ä NNö KSEN HANKKIMINEN ON ASIAKKAAN VASTUULLA. VAROITUS • ä Lä YRITä KORJATA LAITTEISTOA ENNEN KUIN OLET VARMASTI LUKENUT (FI) JA YMMä RTä NYT Tä Mä N HUOLTO-OHJEEN. • MIKä LI Tä Tä VAROITUSTA EI NOUDATETA, SEURAUKSENA VOI OLLA PALVELUNTARJOAJAN, LAITTEISTON Kä YTTä Jä N TAI POTILAAN VAHINGOITTUMINEN Sä HKö ISKUN, MEKAANISEN VIAN TAI MUUN VAARATILANTEEN VUOKSI. ΤΟ ΠΑΡΟΝ ΕΓΧΕΙΡΙΔΙΟ ΣΕΡΒΙΣ ΔΙΑΤΙΘΕΤΑΙ ΣΤΑ ΑΓΓΛΙΚΑ ΜΟΝΟ . • ΕΑΝ ΤΟ ΑΤΟΜΟ ΠΑΡΟΧΗΣ ΣΕΡΒΙΣ ΕΝΟΣ ΠΕΛΑΤΗ ΑΠΑΙΤΕΙ ΤΟ ΠΑΡΟΝ ΕΓΧΕΙΡΙΔΙΟ ΣΕ ΓΛΩΣΣΑ ΕΚΤΟΣ ΤΩΝ ΑΓΓΛΙΚΩΝ , ΑΠΟΤΕΛΕΙ ΕΥΘΥΝΗ ΤΟΥ ΠΕΛΑΤΗ ΝΑ ΠΑΡΕΧΕΙ ΥΠΗΡΕΣΙΕΣ ΜΕΤΑΦΡΑΣΗΣ . • ΜΗΝ ΕΠΙΧΕΙΡΗΣΕΤΕ ΤΗΝ ΕΚΤΕΛΕΣΗ ΕΡΓΑΣΙΩΝ ΣΕΡΒΙΣ ΣΤΟΝ ΕΞΟΠΛΙΣΜΟ ΠΡΟΕΙΔΟΠΟΙΗΣΗ (EL) ΕΚΤΟΣ ΕΑΝ ΕΧΕΤΕ ΣΥΜΒΟΥΛΕΥΤΕΙ ΚΑΙ ΕΧΕΤΕ ΚΑΤΑΝΟΗΣΕΙ ΤΟ ΠΑΡΟΝ ΕΓΧΕΙΡΙΔΙΟ ΣΕΡΒΙΣ . • ΕΑΝ ΔΕ ΛΑΒΕΤΕ ΥΠΟΨΗ ΤΗΝ ΠΡΟΕΙΔΟΠΟΙΗΣΗ ΑΥΤΗ , ΕΝΔΕΧΕΤΑΙ ΝΑ ΠΡΟΚΛΗΘΕΙ ΤΡΑΥΜΑΤΙΣΜΟΣ ΣΤΟ ΑΤΟΜΟ ΠΑΡΟΧΗΣ ΣΕΡΒΙΣ , ΣΤΟ ΧΕΙΡΙΣΤΗ Ή ΣΤΟΝ ΑΣΘΕΝΗ ΑΠΟ ΗΛΕΚΤΡΟΠΛΗΞΙΑ , ΜΗΧΑΝΙΚΟΥΣ Ή ΑΛΛΟΥΣ ΚΙΝΔΥΝΟΥΣ . EZEN KARBANTARTÁSI KÉZIKÖNYV KIZÁRÓLAG ANGOL NYELVEN ÉRHET Ő EL. • HA A VEV Ő SZOLGÁLTATÓJA ANGOLTÓL ELTÉR Ő NYELVRE TART IGÉNYT, AKKOR A VEV Ő FELEL Ő SSÉGE A FORDÍTÁS ELKÉSZÍTTETÉSE. • NE PRÓBÁLJA ELKEZDENI HASZNÁLNI A BERENDEZÉST, AMÍG A FIGYELMEZTETÉS KARBANTARTÁSI KÉZIKÖNYVBEN LEÍRTAKAT NEM ÉRTELMEZTÉK. (HU) • EZEN FIGYELMEZTETÉS FIGYELMEN KÍVÜL HAGYÁSA A SZOLGÁLTATÓ, M Ű KÖDTET Ő VAGY A BETEG ÁRAMÜTÉS, MECHANIKAI VAGY EGYÉB VESZÉLYHELYZET MIATTI SÉRÜLÉSÉT EREDMÉNYEZHETI. - iii

[Page 6] ÞESSI ÞJÓNUSTUHANDBÓK ER EINGÖNGU FÁANLEG Á ENSKU. • EF ÞJÓNUSTUAÐILI VIÐSKIPTAMANNS ÞARFNAST ANNARS TUNGUMÁLS EN ENSKU, ER ÞAÐ Á ÁBYRGÐ VIÐSKIPTAMANNS AÐ ÚTVEGA ÞÝÐINGU. VIÐVÖRUN • REYNIÐ EKKI AÐ ÞJÓNUSTA TÆKIÐ NEMA EFTIR AÐ HAFA SKOÐAÐ OG (IS) SKILIÐ ÞESSA ÞJÓNUSTUHANDBÓK. • EF EKKI ER FARIÐ AÐ ÞESSARI VIÐVÖRUN GETUR ÞAÐ VALDIÐ MEIÐSLUM ÞJÓNUSTUVEITANDA, STJÓRNANDA EÐA SJÚKLINGS VEGNA RAFLOSTS, VÉLRÆNNAR EÐA ANNARRAR HÆTTU. TENTO SERVISNÍ NÁVOD EXISTUJE POUZE V ANGLICKé M JAZYCE. • V P ř íPAD ě , ŽE POSKYTOVATEL SLUŽEB ZÁKAZNÍK Ů M POT ř EBUJE Ná VOD V JINé M JAZYCE, JE ZAJIšT ě Ní P ř EKLADU DO ODPOVíDAJíCíHO JAZYKA ú KOLEM Zá KAZNíKA. • NEPROVÁD Ě JTE ú DRŽBU TOHOTO ZA ř íZENí, ANIŽ BYSTE SI P ř E č ETLI VÝSTRAHA TENTO SERVISNÍ NÁVOD A POCHOPILI JEHO OBSAH. (CS) • V P ř íPAD ě NEDODRŽOVá Ní Té TO VýSTRAHY M ů ŽE DOJíT ÚRAZU ELEKTRICKÁM PROUDEM PRACOVNíKA POSKYTOVATELE SLUŽEB, OBSLUŽNé HO PERSONá LU NEBO PACIENT ů VLIVEM ELEKTRICKé HOP PROUDU, RESPEKTIVE VLIVEM K RIZIKU MECHANICKÉHO POŠKOZENÍ NEBO JINÉMU RIZIKU. DENNE SERVICEMANUAL FINDES KUN PÅ ENGELSK. • HVIS EN KUNDES TEKNIKER HAR BRUG FOR ET ANDET SPROG END ENGELSK, ER DET KUNDENS ANSVAR AT SØRGE FOR OVERSÆTTELSE. ADVARSEL • FORSØG IKKE AT SERVICERE UDSTYRET MEDMINDRE (DA) DENNE SERVICEMANUAL ER BLEVET LÆST OG FORSTÅET. • MANGLENDE OVERHOLDELSE AF DENNE ADVARSEL KAN MEDF Ř RE SKADE P Ĺ GRUND AF ELEKTRISK, MEKANISK ELLER ANDEN FARE FOR TEKNIKEREN, OPERAT Ř REN ELLER PATIENTEN. DEZE ONDERHOUDSHANDLEIDING IS ENKEL IN HET ENGELS VERKRIJGBAAR. • ALS HET ONDERHOUDSPERSONEEL EEN ANDERE TAAL VEREIST, DAN IS DE KLANT VERANTWOORDELIJK VOOR DE VERTALING ERVAN. • PROBEER DE APPARATUUR NIET TE ONDERHOUDEN VOORDAT DEZE WAARSCHUWING ONDERHOUDSHANDLEIDING WERD GERAADPLEEGD EN BEGREPEN IS. (NL) • INDIEN DEZE WAARSCHUWING NIET WORDT OPGEVOLGD, ZOU HET ONDERHOUDSPERSONEEL, DE OPERATOR OF EEN PATIËNT GEWOND KUNNEN RAKEN ALS GEVOLG VAN EEN ELEKTRISCHE SCHOK, MECHANISCHE OF ANDERE GEVAREN. iv -

[Page 7] š Ī APKALPES ROKASGR Ā MATA IR PIEEJAMA TIKAI ANG Ļ U VALOD Ā . • JA KLIENTA APKALPES SNIEDZ Ē JAM NEPIECIEŠAMA INFORM Ā CIJA CIT Ā VALOD Ā , NEVIS ANG Ļ U, KLIENTA PIEN Ā KUMS IR NODROŠIN Ā T TULKOŠANU. BR Ī DIN Ā JUMS • NEVEICIET APR Ī KOJUMA APKALPI BEZ APKALPES ROKASGR Ā MATAS (LV) IZLAS Ī ŠANAS UN SAPRAŠANAS. • Š Ī BR Ī DIN Ā JUMA NEIEV Ē ROŠANA VAR RAD Ī T ELEKTRISK Ā S STR Ā VAS TRIECIENA, MEH Ā NISKU VAI CITU RISKU IZRAIS Ī TU TRAUMU APKALPES SNIEDZ Ē JAM, OPERATORAM VAI PACIENTAM. ŠIS EKSPLOATAVIMO VADOVAS YRA IŠLEISTAS TIK ANGL Ų KALBA. • JEI KLIENTO PASLAUG Ų TEIK Ė JUI REIKIA VADOVO KITA KALBA – NE ANGL Ų , VERTIMU PASIR Ū PINTI TURI KLIENTAS. Į SP Ė JIMAS • NEM Ė GINKITE ATLIKTI Į RANGOS TECHNIN Ė S PRIEŽI Ū ROS DARB Ų , NEBENT (LT) VADOVAUTUM Ė T Ė S ŠIUO EKSPLOATAVIMO VADOVU IR J Į SUPRASTUM Ė TE • NEPAISANT ŠIO PERSP Ė JIMO, PASLAUG Ų TEIK Ė JAS, OPERATORIUS AR PACIENTAS GALI B Ū TI SUŽEISTAS D Ė L ELEKTROS SM Ū GIO, MECHANINI Ų AR KIT Ų PAVOJ Ų . DENNE SERVICEHÅNDBOKEN FINNES BARE PÅ ENGELSK. • HVIS KUNDENS SERVICELEVERANDØR TRENGER ET ANNET SPRÅK, ER DET KUNDENS ANSVAR Å SØRGE FOR OVERSETTELSE. ADVARSEL • IKKE FORSØK Å REPARERE UTSTYRET UTEN AT DENNE (NO) SERVICEHÅNDBOKEN ER LEST OG FORSTÅTT. • MANGLENDE HENSYN TIL DENNE ADVARSELEN KAN FØRE TIL AT SERVICELEVERANDØREN, OPERATØREN ELLER PASIENTEN SKADES PÅ GRUNN AV ELEKTRISK STØT, MEKANISKE ELLER ANDRE FARER. NINIEJSZY PODR Ę CZNIK SERWISOWY DOST Ę PNY JEST JEDYNIE W J Ę ZYKU ANGIELSKIM. • JE ś LI FIRMA ś WIADCZ Ą CA KLIENTOWI US ł UGI SERWISOWE WYMAGA UDOST ę PNIENIA PODR ę CZNIKA W J ę ZYKU INNYM NI Ż ANGIELSKI, OBOWI Ą ZEK ZAPEWNIENIA STOSOWNEGO T ł UMACZENIA SPOCZYWA NA KLIENCIE. OSTRZE Ż ENIE • NIE PRó BOWA ć SERWISOWA ć NINIEJSZEGO SPRZ ę TU BEZ UPRZEDNIEGO (PL) ZAPOZNANIA SI ę Z PODR ę CZNIKIEM SERWISOWYM. • NIEZASTOSOWANIE SI ę DO TEGO OSTRZE Ż ENIA MO ż E GROZI ć OBRA Ż ENIAMI CIA ł A SERWISANTA, OPERATORA LUB PACJENTA W WYNIKU PORA Ż ENIA PR Ą DEM, URAZU MECHANICZNEGO LUB INNEGO RODZAJU ZAGRO Ż E ń . - v

[Page 8] ACEST MANUAL DE SERVICE ESTE DISPONIBIL NUMAI ÎN LIMBA ENGLEZ Ă . • DAC Ă UN FURNIZOR DE SERVICII PENTRU CLIEN Ţ I NECESIT Ă O ALT Ă LIMB Ă DECÂT CEA ENGLEZ Ă , ESTE DE DATORIA CLIENTULUI S Ă FURNIZEZE O TRADUCERE. ATEN Ţ IE • NU ÎNCERCA Ţ I S Ă REPARA Ţ I ECHIPAMENTUL DECÂT ULTERIOR (RO) CONSULT Ă RII Ş I ÎN Ţ ELEGERII ACESTUI MANUAL DE SERVICE. • IGNORAREA ACESTUI AVERTISMENT AR PUTEA DUCE LA R Ă NIREA DEPANATORULUI, OPERATORULUI SAU PACIENTULUI ÎN URMA PERICOLELOR DE ELECTROCUTARE, MECANICE SAU DE ALT Ă NATUR Ă . Да н н о е рук о в о дс т в о п о о бс луж и в а н ию ПРЕДОСТАВЛЯЕТСЯ т о льк о н а а н г ли йс к о м Яз ы к е . • Ес ли с е рв и с н о МУ ПЕРСОНАЛУ к ли е н т а н е о б х о димо рук о в о дс т в о н е н а а н г ли йс к о м ЯЗЫКЕ , к ли е н т у с ле дуе т с а мо с т о Ят е ль н о ОБЕСПЕЧИТЬ п е ре в о д . ОСТОРОЖНО ! • ПЕРЕД ОБСЛУЖИВАНИЕМ ОБОРУДОВАНИЯ ОБЯЗАТЕЛЬНО ОБРАТИТЕСЬ (RU) К ДАННОМУ РУКОВОДСТВУ И ПОЙМИТЕ ИЗЛОЖЕННЫЕ В НЕМ СВЕДЕНИЯ . • НЕСОБЛЮДЕНИЕ УКАЗАННЫХ ТРЕБОВАНИЙ МОЖЕТ ПРИВЕСТИ К ТОМУ , ЧТО СПЕЦИАЛИСТ ПО ТЕХОБСЛУЖИВАНИЮ , ОПЕРАТОР ИЛИ ПАЦИЕНТ ПОЛУЧАТ УДАР ЗЛЕКТРИЧЕСКИМ ТОКОМ , МЕХАНИЧЕСКУЮ ТРАВМУ ИЛИ ДРУГОЕ ПОВРЕЖДЕНИЕ . ТОВА СЕРВИЗНО РЪКОВОДСТВО Е НАЛИЧНО САМО НА АНГЛИЙСКИ ЕЗИК . • АКО ДОСТАВЧИКЪТ НА СЕРВИЗНИ УСЛУГИ НА КЛИЕНТ СЕ НУЖДАЕ ОТ ЕЗИК , РАЗЛИЧЕН ОТ АНГЛИЙСКИ , ЗАДЪЛЖЕНИЕ НА КЛИЕНТА Е ДА ПРЕДОСТАВИ ПРЕВОДАЧЕСКА УСЛУГА . • НЕ СЕ ОПИТВАЙТЕ ДА ИЗВЪРШВАТЕ СЕРВИЗНО ОБСЛУЖВАНЕ НА ТОВА ПРЕДУПРЕЖДЕНИЕ ОБОРУДВАНЕ , ОСВЕН ВСЛУЧАЙ , ЧЕ СЕРВИЗНОТО РЪКОВОДСТВО Е (BG) ПРОЧЕТЕНО И СЕ РАЗБИРА . • НЕСПАЗВАНЕТО НА ТОВА ПРЕДУПРЕЖДЕНИЕ МОЖЕ ДА ДОВЕДЕ ДО НАРАНЯВАНЕ НА ДОСТАВЧИКА НА СЕРВИЗНИ УСЛУГИ , НА ОПЕРАТОРА ИЛИ ПАЦИЕНТА ВСЛЕДСТВИЕНА ТОКОВ УДАР , МЕХАНИЧНИ ИЛИ ДРУГИ РИСКОВЕ . OVAJ PRIRU Č NIK ZA SERVISIRANJE DOSTUPAN JE SAMO NA ENGLESKOM JEZIKU. • AKO KLIJENTOV SERVISER ZAHTEVA JEZIK KOJI NIJE ENGLESKI, ODGOVORNOST JE NA KLIJENTU DA PRUŽI USLUGE PREVO Đ ENJA. UPOZORENJE • NEMOJTE POKUŠAVATI DA SERVISIRATE OPREMU AKO NISTE PRO Č ITALI I (SR) RAZUMELI PRIRU Č NIK ZA SERVISIRANJE. • AKO NE POŠTUJETE OVO UPOZORENJE, MOŽE DO Ć I DO POVRE Đ IVANJA SERVISERA, OPERATERA ILI PACIJENTA UZROKOVANOG ELEKTRI Č NIM UDAROM, MEHANI Č KIM I DRUGIM OPASNOSTIMA. vi -

[Page 9] TA SERVISNI PRIRO Č NIK JE NA VOLJO SAMO V ANGLEŠ Č INI. • Č E PONUDNIK SERVISNIH STORITEV ZA STRANKO POTREBUJE NAVODILA V DRUGEM JEZIKU, JE ZA PREVOD ODGOVORNA STRANKA SAMA. • NE POSKUŠAJTE SERVISIRATI OPREME, NE DA BI PREJ PREBRALI IN OPOZORILO RAZUMELI SERVISNI PRIRO Č NIK. (SL) • Č E TEGA OPOZORILA NE UPOŠTEVATE, OBSTAJA NEVARNOST ELEKTRI Č NEGA UDARA, MEHANSKIH ALI DRUGIH NEVARNOSTI IN POSLEDI Č NIH POŠKODB PONUDNIKA SERVISNIH STORITEV, UPORABNIKA OPREME ALI PACIENTA. OVAJ SERVISNI PRIRU Č NIK DOSTUPAN JE SAMO NA ENGLESKOM JEZIKU. • AKO KLIJENTOV SERVISER ZAHTIJEVA JEZIK KOJI NIJE ENGLESKI, ODGOVORNOST KLIJENTA JE PRUŽITI USLUGE PREVO Đ ENJA. UPOZORENJE • NEMOJTE POKUŠAVATI SERVISIRATI OPREMU AKO NISTE PRO Č ITALI I (HR) RAZUMJELI SERVISNI PRIRU Č NIK. • AKO NE POŠTUJETE OVO UPOZORENJE, MOŽE DO Ć I DO OZLJEDE SERVISERA, OPERATERA ILI PACIJENTA PROUZRO Č ENE STRUJNIM UDAROM, MEHANI Č KIM I DRUGIM OPASNOSTIMA. TÁTO SERVISNÁ PRÍRU Č KA JE K DISPOZíCII LEN V ANGLI Č TINE. • AK ZÁKAZNÍKOV POSKYTOVATE Ľ SLUŽIEB VYŽADUJE INÝ JAZYK AKO ANGLI Č TINU, POSKYTNUTIE PREKLADATE Ľ SKÝCH SLUŽIEB JE ZODPOVEDNOS Ť OU ZÁKAZNÍKA. UPOZORNENIE • NEPOKÚŠAJTE SA VYKONÁVA Ť SERVIS ZARIADENIA SKÔR, AKO SI (SK) NEPRE Č ÍTATE SERVISNÚ PRÍRU Č KU A NEPOROZUMIETE JEJ. • ZANEDBANIE TOHTO UPOZORNENIA Mô ŽE VYÚSTI Ť DO ZRANENIA POSKYTOVATE Ľ A SLUŽIEB, OBSLUHUJú CEJ OSOBY ALEBO PACIENTA ELEKTRICKýM PRú DOM, PRÍPADNE DO MECHANICKé HO ALEBO INé HO NEBEZPE č ENSTVA. DEN HÄR SERVICEHANDBOKEN FINNS BARA TILLGÄNGLIG PÅ ENGELSKA. • OM EN KUNDS SERVICETEKNIKER HAR BEHOV AV ETT ANNAT SPRÅK ÄN ENGELSKA ANSVARAR KUNDEN FÖR ATT TILLHANDAHÅLLA ÖVERSÄTTNINGSTJÄNSTER. VARNING • FÖRSÖK INTE UTFÖRA SERVICE PÅ UTRUSTNINGEN OM DU INTE HAR LÄST (SV) OCH FÖRSTÅR DEN HÄR SERVICEHANDBOKEN. • OM DU INTE TAR HÄNSYN TILL DEN HÄR VARNINGEN KAN DET RESULTERA I SKADOR PÅ SERVICETEKNIKERN, OPERATÖREN ELLER PATIENTEN TILL FÖLJD AV ELEKTRISKA STÖTAR, MEKANISKA FAROR ELLER ANDRA FAROR. - vii

[Page 10] BU SERV İ S KILAVUZU YALNIZCA İ NG İ L İ ZCE OLARAK SA Ğ LANMI Ş TIR. • E Ğ ER MÜ Ş TER İ TEKN İ SYEN İ KILAVUZUN İ NG İ L İ ZCE DI Ş INDAK İ B İ R D İ LDE OLMASINI İ STERSE, KILAVUZU TERCÜME ETT İ RMEK MÜ Ş TER İ N İ N SORUMLULU Ğ UNDADIR. D İ KKAT • SERV İ S KILAVUZUNU OKUYUP ANLAMADAN EK İ PMANLARA MÜDAHALE (TR) ETMEY İ N İ Z. • BU UYARININ GÖZ ARDI ED İ LMES İ , ELEKTR İ K ÇARPMASI YA DA MEKAN İ K VEYA D İĞ ER TÜRDEN KAZALAR SONUCUNDA TEKN İ SYEN İ N, OPERATÖRÜN YA DA HASTANIN YARALANMASINA YOL AÇAB İ L İ R. (JA) Traditional Chinese viii -

[Page 11] (ZH-CN) (KO) - ix

[Page 12] DAMAGE IN TRANSPORTATION All packages should be closely examined at time of delivery. If damage is apparent write “Damage In Shipment” on ALL copies of the freight or express bill BEFORE delivery is accepted or “signed for” by a GE representative or hospital receiving agent. Whether noted or concealed, damage MUST be reported to the carrier immediately upon discovery, or in any event, within 14 days after receipt, and the contents and containers held for inspection by the carrier. A transportation company will not pay a claim for damage if an inspection is not requested within this 14 day period. CERTIFIED ELECTRICAL CONTRACTOR STATEMENT - FOR USA ONLY All electrical Installations that are preliminary to positioning of the equipment at the site prepared for the equipment shall be performed by licensed electrical contractors. Other connections between pieces of electrical equipment, calibrations and testing shall be performed by qualified GE Healthcare personnel. In performing all electrical work on these products, GE will use its own specially trained field engineers. All of GE’s electrical work on these products will comply with the requirements of the applicable electrical codes. The purchaser of GE equipment shall only utilize qualified personnel (i.e., GE’s field engineers, personnel of third-party service companies with equivalent training, or licensed electricians) to perform electrical servicing on the equipment. OMISSIONS & ERRORS If there are any omissions, errors or suggestions for improving this documentation, please contact the GE Healthcare Global Documentation Group with specific information listing the system type, manual title, part number, revision number, page number and suggestion details. Mail the information to: Service Documentation, GE Medical Systems (China) Co., Ltd. No.19 Changjiang Road WuXi National Hi-Tech Development Zone Jiangsu, P.R China 214028 TEL: +86 510 85225888; FAX: +86 510 85226688 GE Healthcare employees should contact the product's Lead Service Integrator (LSI) to report service documentation issues. DO NOT use TrackWise for this purpose. The LSI will then use the internal problem reporting tool to communicate these issues to the writer. SERVICE SAFETY CONSIDERATIONS DANGER DANGEROUS VOLTAGES, CAPABLE OF CAUSING DEATH, ARE PRESENT IN THIS EQUIPMENT. USE EXTREME CAUTION WHEN HANDLING, TESTING AND ADJUSTING. WARNING WARNING Use all Personal Protection Equipment (PPE) such as gloves, safety shoes, safety glasses, and kneeling pad, to reduce the risk of injury. For a complete review of all safety requirements, see the Chapter 1, Safety Considerations section in the Service Manual. x -

[Page 13] LEGAL NOTES The contents of this publication may not be copied or duplicated in any form, in whole or in part, without prior written permission of GE Healthcare. GE Healthcare may revise this publication from time to time without written notice. TRADEMARKS All products and their name brands are trademarks of their respective holders. COPYRIGHTS All Material Copyright© 2004 to 2011 by General Electric Company Inc. All Rights Reserved. - xi

[Page 14] Revision History Revision Date Reason for change 1 23, Qct. 2009 Initial Release 2 13, May 2010 Update for Software update and adding new probes 3 29, June 2010 Update to add Isolation Cart enhanced Version 4 30, November 2010 Update LOGIQ e Spare Parts and add USA CKD address 5 25, April 2011 Add Vivid e R6.x.x 6 25, Sep 2011 Update for LOGIQ e Vet R6.x.x 7 5, Oct 2011 Update for LOGIQ e R7.x.x List of Effected Pages (LOEP) Pages Revision Pages Revision Pages Revision Title Page 7 3-1 to 3-32 7 8-1 to 8-10 7 Warnings i to -xii 7 4-1 to 4-38 7 9-1 to 9-32 7 TOC 7 5-1 to 5-20 7 10-1 to 10-21 7 1-1 to 1-20 7 6-1 to 6-2 7 Index 7 2-1 to 2-10 7 7-1 to 7-28 7 Back Cover N/A xii -

[Page 15] Table of Contents CHAPTER 1 Introduction Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 Purpose of Chapter 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 Chapter Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 Purpose of Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 Typical Users of the Basic Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2 LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Models Covered by this Manual . . 1 - 3 Purpose of Operator Manual(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5 Important Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5 Conventions Used in Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5 Standard Hazard Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6 Product Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 7 Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 11 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 11 Human Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 11 Mechanical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 11 Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 12 Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 13 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 14 Dangerous Procedure Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 16 Lockout/Tagout (LOTO) requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 16 Returning/Shipping Probes and Repair Parts . . . . . . . . . . . . . . . . . . . . . . . 1 - 17 EMC, EMI, and ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 18 Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 18 CE Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 18 Electrostatic Discharge (ESD) Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 18 Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 19 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 19 System Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 20 Factory Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 20 1 Table of Contents

[Page 16] CHAPTER 2 Site preparations Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 Purpose of this chapter 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 Chapter Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 General Console Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 Console Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 EMI Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4 Scan Probe Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5 Facility Needs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6 Recommended Ultrasound Room Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6 Required Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 7 Desirable Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 7 Networking Pre-installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 9 Table of Contents 2

[Page 17] CHAPTER 3 System Setup Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 Purpose of Chapter 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 Average Installation Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2 Installation Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3 Safety Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3 Receiving and Unpacking the Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4 Moving into Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 7 Packing the Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 7 Preparing for Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8 Verify Customer Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8 Physical Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8 EMI Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8 Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 9 Power On / Boot Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 9 Power Off/ Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 10 Transducer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 12 System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 12 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 12 Approved peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 13 Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 14 Peripherals/Accessories Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 14 Available Probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 25 Software/Option Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 27 Connectivity Installation Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 28 Loading Base Image Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 29 Software Version check out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 30 Functional Check-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 30 Paperwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31 Product Locator Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31 User Manual(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31 Table of Contents 3

[Page 18] CHAPTER 4 Functional Checks Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 Purpose for Chapter 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 Required Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 General Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2 Power On/Boot Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2 Power Off/ Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3 Archiving and Loading Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 Adjusting the Display Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6 Lockout/Tagout (LOTO) requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6 System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 7 B Mode Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 10 M Mode Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13 Color Flow Mode Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 16 Doppler Mode Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 20 CWD Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 24 Basic Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 25 Probe/Connectors Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 25 Using Cine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 26 Image Management (QG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 27 Backup and Restore Database, Preset Configurations and Images . . . . . 4 - 28 Software Configuration Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 37 Peripheral Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 37 Table of Contents 4

[Page 19] CHAPTER 5 Components and Functions (Theory) Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 Block Diagrams and Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 External I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5 Power Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6 AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6 Battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7 Air Flow Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8 Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9 Common Service Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 10 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 10 Global Service User Interface (GSUI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 10 Service Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 12 Error Logs Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 13 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 17 Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 18 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 18 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 19 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 19 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 20 PM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 20 Table of Contents 5

[Page 20] CHAPTER 6 Service Adjustments Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 Purpose of this chapter 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 Monitor Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2 Adjustments Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2 Table of Contents 6

[Page 21] CHAPTER 7 Diagnostics/Troubleshooting Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 Purpose of Chapter 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 Gathering Trouble Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Collect Vital System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Collect a Trouble Image with Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3 USB Quick Save. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4 Check and Record the P3 Key Function . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4 Setting the P3 Key to USB Quick Save . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 5 Screen Captures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 6 Check and Record the P1 Key Function . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 6 Setting the P1 Key to Screen Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 6 Capturing a Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 6 Reset the P1 Key to Customer’s Functionality . . . . . . . . . . . . . . . . . . . . . . 7 - 8 Global Service User Interface (GSUI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9 Enter global service user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9 Active Diagnostic Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 10 Control Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 10 Common Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 12 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 12 PC Diagnostics (Non-Interactive Tests) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 13 PC Diagnostics (Interactive Tests) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 14 Restart the system after diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 14 Network and Insite II Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 15 Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 15 Insite II Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 19 Insite II Configuration (For LOGIQ e R6.x.x) . . . . . . . . . . . . . . . . . . . . . . . 7 - 24 Table of Contents 7

[Page 22] CHAPTER 8 Replacement Procedures Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 Purpose of Chapter 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 Disassembly/Re-assembly of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . . . . . . . . . 8 - 1 Warning and Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 Handle Assy (FRU No. 313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 2 Loading Base Image Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4 Checks after FRU replacement (Debrief Guidelines). . . . . . . . . . . . . . . . . . . . . . . . 8 - 9 8 Table of Contents

[Page 23] CHAPTER 9 Renewal Parts Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 Purpose of Chapter 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1 Renewal Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2 Equipment Models Covered in this Chapter . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2 Operator Console Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3 LCD Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 4 Keyboard Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 6 Bottom Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 9 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 14 Isolation Cart Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 15 Isolation Cart Enhanced Version Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 17 Accessories and Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 19 Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 24 Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 29 Table of Contents 9

[Page 24] CHAPTER 10 Care & Maintenance Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 Periodic Maintenance Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 Purpose of Chapter 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1 Why do Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 Keeping Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 Quality Assurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 Maintenance Task Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 How often should care & maintenance tasks be performed? . . . . . . . . . . . . 10 - 2 Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 Special Tools, Supplies and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 5 Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 5 Functional Checks (See Also Chapter 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 6 Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7 Physical Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 8 Optional Diagnostic Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 9 Probe Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 9 Battery Performance Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 10 Electrical Safety Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11 Safety Test Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11 GEMS Leakage Current Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 12 Outlet Test - Wiring Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 13 Chassis Leakage Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 14 Probe Leakage Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 16 When There's Too Much Leakage Current... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 19 10 Table of Contents

[Page 25] Chapter 1 Introduction Section 1-1 Overview 1-1-1 Purpose of Chapter 1 This chapter describes important issues related to safely servicing this ultrasound machine. The service provider must read and understand all the information presented here before installing or servicing a unit. 1-1-2 Chapter Contents Table 1-1 Contents in Chapter 1 Section Description Page Number 1-1 Overview 1-1 1-2 Important Conventions 1-6 1-3 Safety Considerations 1-12 1-4 EMC, EMI, and ESD 1-16 1-5 Customer Assistance 1-17 1-1-3 Purpose of Service Manual This Service Manual provides service information for the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Ultrasound Scanning System. It contains the following chapters: 1.) Chapter 1 - Introduction: Contains a content summary and warnings. 2.) Chapter 2 - Site preparations: Contains pre-installation requirements for the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . 3.) Chapter 3 - System Setup: Contains installation procedures. 4.) Chapter 4 - Functional Checks: Contains functional checks that are recommended as part of the installation, or as required during servicing and periodic maintenance. 5.) Chapter 5 - Components and Functions (Theory): Contains block diagrams and functional explanations of the electronics. 6.) Chapter 6 - Service Adjustments: Contains instructions on how to make available adjustments to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . 7.) Chapter 7 - Diagnostics/Troubleshooting: Provides procedures for running diagnostic or related routines for the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . 8.) Chapter 8 - Replacement Procedures: Provides disassembly procedures and reassembly procedures for all changeable Field Replaceable Units (FRU). 9.) Chapter 9 - Renewal Parts: Contains a complete list of field replaceable parts for the LOGIQ e/ LOGIQ e Vet/LOGIQ i/Vivid e . 10.) Chapter 10 - Care & Maintenance: Provides periodic maintenance procedures for the LOGIQ e/ LOGIQ e Vet/LOGIQ i/Vivid e . Chapter 1 Introduction 1-1

[Page 26] 1-1-4 Typical Users of the Basic Service Manual • Service Personnel (installation, maintenance, etc.). • Hospital’s Service Personnel • Contractors (Some parts of Chapter 2 - Site Preparations) 1-2 Section 1-1 - Overview

[Page 27] 1-1-5 LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Models Covered by this Manual Table 1-2 LOGIQ e R4.x.x Model Designations 5151219 LOGIQ e R4.x.x Console for USA 5151220 LOGIQ e R4.x.x Console for Argentina 5151243 LOGIQ e R4.x.x Console for Europe 5151247 LOGIQ e R4.x.x Console for China 5151252 LOGIQ e R4.x.x Console for Japanese 5151253 LOGIQ e R4.x.x Console for Australia 5151251 LOGIQ e R4.x.x Console for India Table 1-3 LOGIQ e R5.0.x / LOGIQ e Vet Model Designations 5199260 LOGIQ e / LOGIQ e Vet R5.0.x Console for USA 5198329 LOGIQ e / LOGIQ e Vet R5.0.x Console for Argentina 5199670 LOGIQ e / LOGIQ e Vet R5.0.x Console for Europe 5198793 LOGIQ e / LOGIQ e Vet R5.0.x Console for China 5198161 LOGIQ e / LOGIQ e Vet R5.0.x Console for Japanese 5199693 LOGIQ e / LOGIQ e Vet R5.0.x Console for Australia 5212841 LOGIQ e / LOGIQ e Vet R5.0.x Console for India Table 1-4 LOGIQ e R5.2.x Model Designations 5323370 LOGIQ e R5.2.x Console for USA 5323375 LOGIQ e R5.2.xConsole for Argentina 5323371 LOGIQ e R5.2.xConsole for Europe 5323380 LOGIQ e R5.2.xConsole for Japanese 5323378 LOGIQ e R5.2.xConsole for Australia 5323377 LOGIQ e R5.2.x Console for India Table 1-5 LOGIQ e R6.x.x Model Designations 5389028 LOGIQ e R6.x.x Console for USA 5389808 LOGIQ e R6.x.x Console for Argentina 5389810 LOGIQ e R6.x.x Console for Europe 5389811 LOGIQ e R6.x.x Console for Chinese 5389812 LOGIQ e R6.x.x Console for Japanese 5389813 LOGIQ e R6.x.x Console for Australia 5389814 LOGIQ e R6.x.x Console for India 5410642 LOGIQ e R6.x.x Console for CKD USA 5410642 LOGIQ e R6.x.x Console for CKD Taiwan Chapter 1 Introduction 1-3

[Page 28] Table 1-6 LOGIQ e R6.x.x Model Designations 5432745 LOGIQ e R7.x.x Console for USA 5432746 LOGIQ e R7.x.x Console for Europe 5432747 LOGIQ e R7.x.x Console for Japan Table 1-7 LOGIQ i R4.x.x Model Designations 5176830 LOGIQ i R4.1.x Console for USA 5179969 LOGIQ i R4.1.x Console for Argentina 5179685 LOGIQ i R4.1.x Console for Europe 5179209 LOGIQ i R4.1.x Console for China 5179748 LOGIQ i R4.1.x Console for Japanese 5179191 LOGIQ i R4.1.x Console for Australia 5179176 LOGIQ i R4.1.x Console for India Table 1-8 LOGIQ i R5.x.x Model Designations 5245475 LOGIQ i R5.x.x Console for USA 5245476 LOGIQ i R5.x.x Console for Argentina 5245477 LOGIQ i R5.x.x Console for Europe 5245478 LOGIQ i R5.x.x Console for China 5245480 LOGIQ i R5.x.x Console for Australia 5245481 LOGIQ i R5.x.x Console for India Table 1-9 Vivid e R4.x.x Model Designations 5171613 Vivid e R4.x.x Console for USA 5172528 Vivid e R4.x.x Console for Argentina 5171633 Vivid e R4.x.x Console for Europe 5171603 Vivid e R4.x.xConsole for China 5171755 Vivid e R4.x.x Console for Japanese 5172272 Vivid e R4.x.x Console for Australia 5172286 Vivid e R4.x.x Console for India/South Africa 5183318 Vivid e R4.x.x Console with SKD ECG Table 1-10 Vivid e R5.x.x Model Designations 5198601 Vivid e R5.x.x Console for USA 5212203 Vivid e R5.x.x Console for Argentina 5212894 Vivid e R5.x.x Console for Asia 1-4 Section 1-1 - Overview

[Page 29] Table 1-10 Vivid e R5.x.x Model Designations 5199815 Vivid e R5.x.x Console for China 5213329 Vivid e R5.x.x Console for Japan 5212851 Vivid e R5.x.x Console for Australia 5199644 Vivid e R5.x.x Console for India/South Africa 5183318 Vivid e R5.x.x Console with SKD ECG for Europe Table 1-11 Vivid e R6.x.x Model Designations 5411312 Vivid e R6.x.x Console for EU 5411381 Vivid e R6.x.x Console for USA 5411382 Vivid e R6.x.x Console for China 5411383 Vivid e R6.x.x Console for Argentina 5411384 Vivid e R6.x.x Console for Japan 5411385 Vivid e R6.x.x Console for Australia 5411386 Vivid e R6.x.x Console for India 5411388 Vivid e R6.x.x Console for SKD ECG 5410641 Vivid e R6.x.x Console for CKD Taiwan Table 1-12 LOGIQ e Vet R6.x.x Model Designations 5198415-2 LOGIQ e Vet R6.x.x Console for EU 5199518-2 LOGIQ e Vet R6.x.x Console for USA 1-1-6 Purpose of Operator Manual(s) The Operator Manual(s) should be fully read and understood before operating the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e and also kept near the unit for quick reference. Chapter 1 Introduction 1-5

[Page 30] Section 1-2 Important Conventions 1-2-1 Conventions Used in Book Icons Pictures, or icons, are used wherever they reinforce the printed message. The icons, labels and conventions used on the product and in the service information are described in this chapter. Safety Precaution Messages Various levels of safety precaution messages may be found on the equipment and in the service information. The different levels of concern are identified by a flag word that precedes the precautionary message. Known or potential hazards are labeled in one of following ways: DANGER DANGER IS USED TO INDICATE THE PRESENCE OF A HAZARD THAT WILL CAUSE SEVERE PERSONAL INJURY OR DEATH IF THE INSTRUCTIONS ARE IGNORED. WARNING WARNING WARNING IS USED TO INDICATE THE PRESENCE OF A HAZARD THAT CAN CAUSE SEVERE PERSONAL INJURY AND PROPERTY DAMAGE IF INSTRUCTIONS ARE IGNORED. CAUTION Caution is used to indicate the presence of a hazard that will or can cause minor personal injury and property damage if instructions are ignored. NOTICE Equipment Damage Possible Notice is used when a hazard is present that can cause property damage but has absolutely no personal injury risk. Example : Disk drive will crash. NOTE: Notes provide important information about an item or a procedure. Information contained in a NOTE can often save you time or effort. 1-6 Section 1-2 - Important Conventions

[Page 31] 1-2-2 Standard Hazard Icons Important information will always be preceded by the exclamation point contained within a triangle, as seen throughout this chapter. In addition to text, several different graphical icons (symbols) may be used to make you aware of specific types of hazards that could cause harm. Table 1-13 Standard Hazard Icons ELECTRICAL MECHANICAL RADIATION LASER HEAT PINCH LASER LIGHT Other hazard icons make you aware of specific procedures that should be followed. Table 1-14 Standard Icons Indicating a Special Procedure Be Used AVOID STATIC ELECTRICITY TAG AND LOCK OUT WEAR EYE PROTECTION TAG LOCKOUT EYE PROTECTION Signed Date Chapter 1 Introduction 1-7

[Page 32] 1-2-3 Product Icons The following table describes the purpose and location of safety labels and other important information provided on the equipment. Identification and Rating Plate • Manufacture’s name and address Bottom panel of the console • Date of manufacture • Model and serial numbers • Electrical ratings (Volts, Amps, phase, and frequency) Type/Class Label Used to indicate the degree of safety or Bottom panel of the adapter. protection. IP Code (IPX1 or IPX8) Indicates the degree of protection Bottom of Footswitch IPX1: FSU-2001 provided by the enclosure per IEC60 IPX8: MKF 2-MED GP26, FSU-1000 529. IPX1 cannot be used in operating room environment; IPX8 can be used in operating room environment. Authorized European Representative Bottom panel address United States only Prescription Bottom panel Requirement label Equipment Type BF (man in the box symbol) IEC 878-02-03 indicates B Probe connectors Type equipment having a floating applied part. General Warning. Various “CAUTION - Dangerous voltage” (the lightning flash with arrowhead in Various equilateral triangle) is used to indicate electric shock hazards. 1-8 Section 1-2 - Important Conventions

[Page 33] “Protective Earth” indicates the Inside of AC adapter protective earth (grounding) terminal. “ON” indicates the power on position of the power switch. CAUTION Stick to Power Switch This Power Switch DOES NOT ISOLATE Mains Supply “TUV” Listing and Certification Mark is used to designate conformance to nationally recognized product safety standards. The Mark bears the name Bottom panel of the console and /or logo of the testing laboratory, product category, safety standard is assessed and a control number. Date of manufacture. The date could be a year, year and month, or year, month and day, as Rating Plate appropriate. See ISO 8601 for date formates. Catalog or model number. Rating Plate REF REF Serial number Rating Plate SN SN Direct Current. For products to be powered from a DC Rating Plate supply. Input Rating Plate For use with adapter model TWADP Rating Plate Description Rating Plate Type CF Defib-Proof Applied Part (heart in the box with paddle) symbolis in ECG Module accordance with IEC 60878-02-06. Chapter 1 Introduction 1-9

[Page 34] “Consult accompanying documents” is intended to alert the user to refer to the operator manual or other instructions Various when complete information cannot be provided on the label. Rear of Docking Cart and rear of Do not push the system. Isolation Cart. This symbol indicates that the waste of electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Please contact an Rating Plate authorized representative of the manufacturer for information concerning the decommissioning of your equipment. When closing the LCD cover, use caution to avoid injuring hands or fingers as there is a closing mechanism Rating Plate which allows the LCD cover to automatically close. Indicates the product contains hazardous materials in excess of the limits established by Chinese standard SJ/T11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. The number in the symbol is the Environment-friendly Use Period (EFUP), which indicates the Rear panel, rating plate period during which the toxic or hazardous substances or elements contained in electronic information products will not leak or mutate under normal operating conditions so that the use of such electronic information products will not result in any severe environmental pollution, any bodily injury or damage to any assets. This product consists of devices that may contain mercury, which must be recycled or disposed of in accordance Bottom panel of the console with local, state, or country laws. (Within this system, the backlight lamps in the monitor display contain mercury.) 1-10 Section 1-2 - Important Conventions

[Page 35] The separate collection symbol is affixed to a battery, or its packaging, to advise you that the battery must be recycled or disposed of in accordance with local or country laws. The letters below the separate collection symbol indicate whether certain elements (Pb=Lead, Cd=Cadmium, Hg=Mercury) are contained in the battery. To minimize potential effects on the environment and human health, it is important that all marked batteries that you remove from the product are properly recycled or Battery Pack disposed. For information on how the battery may be safely removed from the device, please consult the service manual or equipment instructions. Information on the potential effects on the environment and human health of the substances used in batteries is available at this url: http:// www.gehealthcare.com/euen/weee- recycling/index.html No hazardous substance, above the maximum concentration value, is present. Maximum concentration values for electronic information products, as set by the People’s Republic of China Electronic Industry Standard SJ/ T11364-2006, include the hazardous substances of lead, mercury, hexavalent chromium, cadmium, polybrominated biphenyl (PBB), and polybrominated diphenyl ether (PBDE). Do not connect the DVD-RW to the DVD-RW system while scanning. GOST Symbol. Russia Regulatory Bottom Country Clearance. Chapter 1 Introduction 1-11

[Page 36] Section 1-3 Safety Considerations 1-3-1 Introduction The following safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual, violates safety standards of design, manufacture and intended use of the equipment. 1-3-2 Human Safety Operating personnel must not remove the system covers. Servicing should be performed by authorized personnel only. Only personnel who have participated in a LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Training are authorized to service the equipment. 1-3-3 Mechanical Safety WARNING WARNING Ultrasound probes are highly sensitive medical instruments that can easily be damaged by improper handling. Use care when handling and protect from damage when not in use. Do not use a damaged or defective probe. Failure to follow these precautions can result in serious injury and equipment damage. WARNING WARNING Never use a probe that has fallen to the floor. Even if it looks ok, it may be damaged. CAUTION The LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e weights 4.6kg or more, depending on installed peripherals, when ready for use. To avoid possible injury and equipment damage: ALWAYS: • Use the handle to move the system. • Do not let the system strike walls or door frame. • Limit movement to a slow careful walk. NOTE: Special care should be taken when transporting the unit in a vehicle: • Before transporting, place the system in its special storage case. • Ensure that the system is firmly secured while inside the vehicle. • Secure system with straps or as directed otherwise to prevent motion during transport. • Prevent vibration damage by driving cautiously. Avoid unpaved roads, excessive speeds, and erratic stops or starts. 1-3-4 Electrical Safety To minimize shock hazard, the equipment chassis must be connected to an electrical ground. The system is equipped with a three-conductor AC power cable. This must be plugged into an approved electrical outlet with protective ground. The power outlet used for this equipment should not be shared with other types of equipment. Both the system power cable and the power connector meet international electrical standards. 1-3-5 Label Location Please refer to Basic User Manual for label location information. 1-12 Section 1-3 - Safety Considerations

[Page 37] 1-3-6 Battery Safety To avoid the risk of injury, follow the warning and cautions to make sure that the battery does not burst, ignite, or generate heat of fumes. • The battery has a safety device. Do not disassemble or alter the battery. WARNING WARNING • Charge and discharge the batteries only when the ambient temperature is between 10 and 40 C (50 F and 122 F). • Do not short-circuit the battery by directly connecting the negative terminals with metal objects. • Do not heat the battery or discard it in a fire. • Do not expose the battery to temperature over 50 ° C (122 ° F). Keep it away from fire and other heat sources. • Do not charge the battery near a heat source, such as a fire or heater. • Do not leave the battery in direct sunlight. • Do not drop packs from height to prevent them from possible malfunction damage. • Do not pierce the battery with a sharp object, hit it, or step on it. • Do not use a damaged battery. • Do not solder a battery. • Do not connect the battery to an electrical power outlet. • Do not contact PCM ( Power Control and Monitor, it’s a small board in the battery) directly to prevent packs from ESD damage. • In case of longer non-use of the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e , please make sure the battery is removed. CAUTION To avoid the battery bursting, igniting, or fumes from the battery causing equipment damage, observe the following precautions: • Do not immerse the battery in water or allow it to get wet. • Do not put the battery into a microwave oven or pressurized container. • If the battery leaks or emits an odor, remove it from all possible flammable sources. • If the battery emits an odor or heat, is deformed or discolored, or in a way appears abnormal during use, recharging or storage, immediately remove it and stop using it. If you have any questions about the battery, consult GE or your local representative. • Short term (less than one month) storage of battery pack: • Store the battery in a temperature range between 0 ° C (32 ° F) and 50 ° C (122 ° F). • Use only GE recognized batteries. • In case of the long term (3 months or more) storage: • Store the battery in a temperature range of -20 ° C (-4 ° F) and 45 ° C (113 ° F). • When charging for the first time after long-term storage. Recover such packs to original performance through repeating several cycles of full charging and discharging. • When store packs for more than 6 months, charge at lease once charging require per 6 months to prevent leakage and deterioration in performance due to self- discharging. • When the system isn't powered on continuously more than 6 months, in order to prevent leakage and deterioration in performance of CMOS battery, power on the system at least once per 6 months for more than 10 hours to have CMOS battery fully charged. Time and date need to be re-setup. NOTICE The battery shall be shipped in about 30% charged state. Those packs have to be fully charged and discharged up to 3 times to utilize Li-lon smart packs before use. Chapter 1 Introduction 1-13

[Page 38] 1-3-7 Dangerous Procedure Warnings Warnings, such as the examples below, precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. DANGER DANGEROUS VOLTAGES, CAPABLE OF CAUSING DEATH, ARE PRESENT IN THIS EQUIPMENT. USE EXTREME CAUTION WHEN HANDLING, TESTING AND ADJUSTING. WARNING WARNING EXPLOSION WARNING DO NOT OPERATE THE EQUIPMENT IN AN EXPLOSIVE ATMOSPHERE. OPERATION OF ANY ELECTRICAL EQUIPMENT IN SUCH AN ENVIRONMENT CONSTITUTES A DEFINITE SAFETY HAZARD. WARNING WARNING DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT BECAUSE OF THE DANGER OF INTRODUCING ADDITIONAL HAZARDS, DO NOT INSTALL SUBSTITUTE PARTS OR PERFORM ANY UNAUTHORIZED MODIFICATION OF THE EQUIPMENT. WARNING WARNING SHUT DOWN FORCEDLY OR PLUG IN/OUT ACDC INVALID MAY CAUSE THE DAMAGE OF SYSTEM FILES. 1-3-8 Lockout/Tagout (LOTO) requirements Follow OSHA Lockout/Tagout requirements (USA) or local Lockout/Tagout requirements by ensuring you are in total control of the AC power plug at all times during the service process. To apply Lockout/Tagout: 1.) Plan and prepare for shutdown. 2.) Shutdown the equipment. 3.) Isolate the equipment. 4.) Apply Lockout/Tagout Devices. 5.) Remove battery. 6.) Control all stored and residual energy. 7.) Verify isolation. All potentially hazardous stored or residual energy is relieved. NOTICE Energy Control and Power Lockout for LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e WHEN SERVICING PARTS OF THE SYSTEM WHERE THERE IS EXPOSURE TO VOLTAGE GREATER THAN 30 VOLTS: 1. TURN OFF THE SCANNER. 2. UNPLUG THE SYSTEM. 3. MAINTAIN CONTROL OF THE SYSTEM POWER PLUG. 4. WAIT FOR AT LEAST 20 SECONDS FOR CAPACITORS TO DISCHARGE AS THERE ARE NO TAG & TEST POINTS TO VERIFY ISOLATION. THE AMBER LIGHT ON THE OP PANEL ON/OFF BUTTON LOCKOUT WILL TURN OFF. Signed Date 5. REMOVE THE SYSTEM BATTERY. 1-14 Section 1-3 - Safety Considerations

[Page 39] 1-3-9 Returning/Shipping Probes and Repair Parts Equipment being returned must be clean and free of blood and other infectious substances. GEMS policy states that body fluids must be properly removed from any part or equipment prior to shipment. GEMS employees, as well as customers, are responsible for ensuring that parts/equipment have been properly decontaminated prior to shipment. Under no circumstance should a part or equipment with visible body fluids be taken or shipped from a clinic or site (for example, body coils or an ultrasound probe). The purpose of the regulation is to protect employees in the transportation industry, as well as the people who will receive or open this package. NOTE: The US Department of Transportation (DOT) has ruled that “items that were saturated and/or dripping with human blood that are now caked with dried blood; or which were used or intended for use in patient care” are “regulated medical waste” for transportation purposes and must be transported as a hazardous material. NOTE: The USER/SERVICE staff should dispose all the waste properly as per federal, state, and local waste disposal regulation. The ultrasound system is not meant to be long term storage of patient data or images. The user us responsible for the date on the system and a regular backup is highly recommended. If the system is sent for repair, please ensure that any patient information is backup and erased from the system before shipping. It is always possible during system failure and repair to lose patient data. GE is not responsible for the loss of this data. If PHI (Patient Healthcare Information) data needs to be sent to GE employees for service purposes, GE will ascertain agreement from the customer. The patient information shall only be transferred by approved service processes, tools and devices restricting access, protecting or encrypting data where required, and providing traceability in the form of paper or electronic documents at each stage of the procedure while maintaining compliance with cross-border restrictions of patient information transfers. Chapter 1 Introduction 1-15

[Page 40] Section 1-4 EMC, EMI, and ESD 1-4-1 Electromagnetic Compatibility (EMC) Electromagnetic compatibility describes a level of performance of a device within its electromagnetic environment. This environment consists of the device itself and its surroundings including other equipment, power sources and persons with which the device must interface. Inadequate compatibility results when a susceptible device fails to perform as intended due interference from its environment or when the device produces unacceptable levels of emission to its environment. This interference is often referred to as radio–frequency or electromagnetic interference (RFI/EMI) and can be radiated through space or conducted over interconnecting power of signal cables. In addition to electromagnetic energy, EMC also includes possible effects from electrical fields, magnetic fields, electrostatic discharge and disturbances in the electrical power supply. 1-4-2 CE Compliance The LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e unit conforms to all applicable conducted and radiated emission limits and to immunity from electrostatic discharge, radiated and conducted RF fields, magnetic fields and power line transient requirements. For applicable standards refer to the Safety Chapter in the Basic User Manual. NOTE: For CE Compliance, it is critical that all covers, screws, shielding, gaskets, mesh, clamps, are in good condition, installed tightly without skew or stress. Proper installation following all comments noted in this service manual is required in order to achieve full EMC performance. 1-4-3 Electrostatic Discharge (ESD) Prevention WARNING WARNING DO NOT TOUCH ANY BOARDS WITH INTEGRATED CIRCUITS PRIOR TO TAKING THE NECESSARY ESD PRECAUTIONS: 1.FOLLOW GENERAL GUIDELINES FOR HANDLING OF ELECTROSTATIC SENSITIVE EQUIPMENT. 1-16 Section 1-4 - EMC, EMI, and ESD

[Page 41] Section 1-5 Customer Assistance 1-5-1 Contact Information If this equipment does not work as indicated in this service manual or in the User Manual, or if you require additional assistance, please contact the local distributor or appropriate support resource, as listed below. Prepare the following information before you call: - System ID serial number. - Software version. Table 1-16 Phone Numbers for Customer Assistance Location Phone Number USA Service: On-site 1-800–437–1171 GE Medical Systems Ultrasound Service Engineering Service: Parts 1-800-558-2040 9900 Innovation Drive Wauwatosa, WI 53226 Applications support 1-800-682-5327 or 1-262-524-5698 Canada 1-800-668-0732 Service 1-800-321-7937 Latin America Applications support 1-262-524-5698 Europe GE Ultraschall Deutschland GmbH& Co. KG Phone: +33 (0)130-831-300 (General Imaging and Cardiac) BeethovenstraBe 239 Postfach 11 05 60, D-42665 Solingen Fax: +49 (0)212-2802-431 Germany Asia (Singapore) Tel: +65 291-8528 GE Ultrasound Asia Service Department - Ultrasound 298 Tiong Bahru Road #15-01/06 Central Plaza Fax: +65 6291-7006 Singapore 169730 Phone: 81-42-648-2944 Japan Support Center Fax: 81-42-648-2905 Chapter 1 Introduction 1-17

[Page 42] 1-5-2 System Manufacturer Table 1-17 System Manufacturer Manufacturer Phone Number GE Medical Systems (China) Co., Ltd. TEL: +86 510-85225888 No.19, Changjiang Road, Wuxi National Hi-Tech Dev. Zone, Jiangsu, FAX: +86 510-85226688 P.R.China 214028 1-5-3 Factory Sites Table 1-18 Factory Sites Manufacturer Phone Number GE Medical Systems (China) Co., Ltd. TEL: +86 510-85225888 No.19, Changjiang Road, Wuxi National Hi-Tech Dev. Zone, Jiangsu, FAX: +86 510-85226688 P.R.China 214028 GE Ultrasound Korea: TEL: +82-31-740-6112 65-1, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, FAX: +82-31-740-6435 Korea 462-120 GE Medical Systems Ultrasound & Primary Care Diagnostics, LLC DBA GE Healthcare TEL: (1) 800-437-1171 9900 Innovation Drive FAX: (1) 414-721-3865 Wauwatosa, WI 53226 U.S.A 1-18 Section 1-5 - Customer Assistance

[Page 43] Chapter 2 Site preparations Section 2-1 Overview 2-1-1 Purpose of this chapter 2 This chapter provides the information required to plan and prepare for the installation of a LOGIQ e/ LOGIQ e Vet/LOGIQ i/Vivid e . Included are descriptions of the facility and electrical needs to be met by the purchaser of the unit. 2-1-2 Chapter Contents Table 2-1 Contents in Chapter 2 Section Description Page Number 2-1 Overview 2-1 2-2 General Console Requirements 2-2 2-3 Facility Needs 2-6 Chapter 2 Site preparations 2-1

[Page 44] Section 2-2 General Console Requirements 2-2-1 Console Environmental Requirements Table 2-2 Environmental Requirements for LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Scanners Operational Storage Transport Temperature 10 - 40 degree C -5 - 50 degree C -5 - 50 degree C 30 - 75% 10 - 90% 10 - 90% Humidity non-condensing non-condensing non-condensing Pressure 700 - 1060hPa 700 - 1060hPa 700 - 1060hPa Temperatures in degree C, conversion to degree F =(degree C*(9/5) + 32) 2-2-1-1 Lighting Bright light is needed for system installation, updates and repairs. However, operator and patient comfort may be optimized if the room light is subdued and indirect. Therefore a combination lighting system (dim/bright) is recommended. Keep in mind that lighting controls and diameters can be a source of EMI which could degrade image quality. These controls should be selected to minimize possible interface. 2-2-2 Electrical Requirements NOTE: GE Medical Systems requires a dedicated power and ground for the proper operation of its Ultrasound equipment. This dedicated power shall originate at the last distribution panel before the system. Sites with a mains power system with defined Neutral and Live: The dedicated line shall consist of one phase, a neutral (not shared with any other circuit), and a full size ground wire from the distribution panel to the Ultrasound outlet. Sites with a mains power system without a defined Neutral: The dedicated line shall consist of one phase (two lines), not shared with any other circuit, and a full size ground wire from the distribution panel to the Ultrasound outlet. Please note that image artifacts can occur, if at any time within the facility, the ground from the main facility's incoming power source to the Ultrasound unit is only a conduit. 2-2-2-1 LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Power Requirements Table 2-3 Electrical Specifications for LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Adapter Voltage Power Current Frequency TWADP100 100-240 VAC 130VA max. 1.3 A (max.) 50/ 60HZ 2-2 Section 2-2 - General Console Requirements

[Page 45] 2-2-2-2 Inrush Current Inrush current is not a factor to consider due to the inrush current limiting properties of the power supplies. Table 2-4 Inrush Current Inrush Current Voltage Console Only Console with all peripherals 100V 0.38A 0.41A 240V 0.20A 0.21A 2-2-2-3 Site Circuit Breaker It is recommended that the branch circuit breaker for the machine be readily accessible. 2-2-2-4 Site Power Outlets A dedicated AC power outlet must be within reach of the unit without extension cords. Other adequate outlets for the external peripherals, medical and test equipment needed to support this unit must also be present within 1 m (3.2 ft.) of the unit. Electrical installation must meet all current local, state, and national electrical codes. 2-2-2-5 Unit Power Plug If the unit arrives without a power plug, or with the wrong plug, you must contact your GE dealer or the installation engineer must supply what is locally required. 2-2-2-6 Power Stability Requirements Voltage drop-out Max 10 ms. Power Transients (All applications) Less than 25% of nominal peak voltage for less than 1 millisecond for any type of transient, including line frequency, synchronous, asynchronous, or aperiodic transients. Chapter 2 Site preparations 2-3

[Page 46] 2-2-3 EMI Limitations Ultrasound machines are susceptible to Electromagnetic Interference (EMI) from radio frequencies, magnetic fields, and transient in the air wiring. They also generate EMI. The LOGIQ e/LOGIQ e Vet/ LOGIQ i/Vivid e complies with limits as stated on the EMC label. However there is no guarantee that interface will not occur in a particular installation. Possible EMI sources should be identified before the unit is installed. Electrical and electronic equipment may produce EMI unintentionally as the result of defect. These sources include: • medical lasers, • scanners, • cauterizing guns, • computers, • monitors, • fans, • gel warmers, • microwave ovens, • light dimmers, • portable phones. The presence of a broadcast station or broadcast van may also cause interference. See Table 2-5 for EMI Prevention tips. Table 2-5 EMI Prevention/abatement EMI Rule Details Keep the unit at least 5 meters or 15 feet away from other EMI sources. Special shielding Be aware of RF sources may be required to eliminate interference problems caused by high frequency, high powered radio or video broadcast signals. Poor grounding is the most likely reason a unit will have noisy images. Check grounding of Ground the unit the power cord and power outlet. After you finish repairing or updating the system, replace all covers and tighten all screws. Replace all screws, RF Any cable with an external connection requires a magnet wrap at each end. Install the gaskets, covers, cores shield over the front of card cage. Loose or missing covers or RF gaskets allow radio frequencies to interfere with the ultrasound signals. If more than 20% or a pair of the fingers on an RF gasket are broken, replace the gasket. Replace broken RF gaskets Do not turn on the unit until any loose metallic part is removed. Do not place labels where RF Never place a label where RF gaskets meet the unit. Otherwise, the gap created will permit gaskets touch metal RF leakage. Or, if a label has been found in such a position, move the label. Use GE specified harnesses The interconnect cables are grounded and require ferrite beads and other shielding. Also, and peripherals cable length, material, and routing are all important; do not change from what is specified. Take care with cellular phones Cellular phones may transmit a 5 V/m signal; that could cause image artifacts. Do not allow cables to lie across the top of the card cage or hang out of the peripheral bays. Properly dress peripheral Loop the excess length for peripheral cables inside the peripheral bays. Attach the monitor cables cables to the frame. 2-4 Section 2-2 - General Console Requirements

[Page 47] 2-2-4 Scan Probe Environmental Requirements Operation:10° to 40° C Storage:-10° to 50° C NOTE: The recommended storage temperature range of 6Tc-RS is between 0°C and 45°C. NOTE: Temperature in degrees C. Conversion to Degrees F = (Degrees C * (9/5) + 32). NOTICE SYSTEMS AND ELECTRONIC PROBES ARE DESIGNED FOR STORAGE TEMPERATURES OF -10 TO + 60 degrees C. WHEN EXPOSED TO LARGE TEMPERATURE VARIATIONS, THE PRODUCT SHOULD BE KEPT IN ROOM TEMPERATURE FOR 10 HOURS BEFORE USE. Chapter 2 Site preparations 2-5

[Page 48] Section 2-3 Facility Needs 2-3-1 Recommended Ultrasound Room Layout 2-3-1-1 Purchaser Responsibilities The work and materials needed to prepare the site is the responsibility of the purchaser. Delay, confusion, and waste of manpower can be avoided by completing pre installation work before delivery. User the Pre Installation checklist to verify that all needed steps have been taken, Purchaser reasonability includes: • Procuring the materials required. • Completing the preparations before delivery of the ultrasound system. • Paying the costs for any alternations and modifications not specifically provided in the sales contract. NOTE: All electrical installation that are preliminary to the positioning of the equipment at the site prepared for the equipment must be performed by licensed electrical contractors. Other connections between pieces of electrical equipment, products involved (and the accompanying electrical installations) are highly sophisticated and special engineering competence is required. All electrical work on these product must comply with the requirements of applicable electrical codes. The purchaser of GE equipment must only utilize qualified personnel to perform electrical servicing on the equipment. The desire to use a non-listed or customer provided product or to place an approved product further from the system than the interface kit allows presents challenges to the installation team. To avoid delays during installation, such variances should be made known to the individuals or group performing the installation at the earliest possible date (preferable prior to purchase). The ultrasound suite must be clean prior to delivery of the machine. Carpet is not recommended because it collects dust and creates static. Potential sources of EMI (electromagnetic interference) should also be investigated before delivery. Dirt, static, and EMI can negatively impact system. 2-6 Section 2-3 - Facility Needs

[Page 49] 2-3-2 Required Features NOTE: GE Medical Systems requires a dedicated power and ground for the proper operation of its Ultrasound equipment. This dedicated power shall originate at the last distribution panel before the system. Sites with a mains power system with defined Neutral and Live: The dedicated line shall consist of one phase, a neutral (not shared with any other circuit), and a full size ground wire from the distribution panel to the Ultrasound outlet. Sites with a mains power system without a defined Neutral: The dedicated line shall consist of one phase (two lines), not shared with any other circuit, and a full size ground wire from the distribution panel to the Ultrasound outlet. Please note that image artifacts can occur, if at any time within the facility, the ground from the main facility's incoming power source to the Ultrasound unit is only a conduit. • Dedicated single branch power outlet of adequate amperage meeting all local and national codes which is located less than 2.5 m (8 ft.) from the unit’s proposed location • Door opening is at least 76 cm (30 in) wide • Proposed location for unit is at least 0.2m (0.67 ft.) from the wall for cooling • Power outlet and place for any external peripheral are within 2 m (6.5 ft.) of each other with peripheral within 1 m of the unit to connect cables. • Power outlets for other medical equipment and gel warmer • Power outlets for test equipment and modem within 1 m (3.2 ft.) of unit • Clean and protected space to store transducers (in their cases or on a rack) • Material to safely clean probes (done with a plastic container, never metal) 2-3-3 Desirable Features • Door is at least 92 cm (3 ft.) wide • Circuit breaker for dedicated power outlet is easily accessible • Sink with hot and cold water • Receptacle for bio–hazardous waste, like used probe sheaths • Emergency oxygen supply • Storage for linens and equipment • Nearby waiting room, lavatory, and dressing room • Dual level lighting (bright and dim) • Lockable cabinet ordered by GE for its software and proprietary manuals. Chapter 2 Site preparations 2-7

[Page 50] 2-3-3-1 Recommended and Alternate Ultrasound Room Layout Recommended standard floor plan and a minimal floor plan for ultrasound equipment: 18 IN . (46 C M ) LINEN SUPPLY D E D I C AT E D P O W E R , R E C EP TA C LE C O NS O LE FILM P R O C ESSIN G R OOM O N FILM V IEW E R FOOT S W INAT I FILE C O UN T E R TO P C O UN T E R TO P S TOO L C AB INET E XAM TAB LE SIN K 76 IN . (193 C M ) SU C T I O N LINE 24 IN . E M E R G E C Y (61 C M ) OX Y G EN SE CR E TA R YS O R D O C TO R ’ S D ES K O V E R H E A D P AT IENT LIG H T S D I MM E R TO ILET FA C ILI T Y D OO R 42 IN . (107 C M ) A 14 by 17 foot R ecommended Floor Plan S cale : Each square equals one square foot FILM V IEW E R LINEN SUPPLY SIN K FILM SUPPLIES P R OB ES /SUPPLIES E XT E R N A L PE R IPH E R A LS D E D I C AT E D PO W E R O U T LE T S FOOT LO G I Q B oo k X P S W S TOO L C O NS O LE E XAM INA R I O N G E C AB INET 24 IN . TAB LE FOT SO FT W A R E (61 C M ) 76 IN . A N D MA NU A LS (193 C M ) D OO R 30 IN . (76 C M ) A n 8 by 10 foot M inimal Floor Plan Figure 2-1 RECOMMENDED ULTRASOUND ROOM LAYOUT 2-8 Section 2-3 - Facility Needs

[Page 51] 2-3-4 Networking Pre-installation Requirements 2-3-4-1 Stand Alone Scanner (without Network Connection) None. 2-3-4-2 Scanner Connected to Hospital’s Network Supported networks: Wireless LAN 2-3-4-3 Purpose of DICOM Network Function DICOM services provide the operator with clinically useful features for moving images and patient information over a hospital network. Examples of DICOM services include the transfer of images to workstations for viewing or transferring images to remote printers. As an added benefit, transferring images in this manner frees up the on-board monitor and peripherals, enabling viewing to be done while scanning continues. With DICOM, images can be archived, stored, and retrieved faster, easier, and at a lower cost. 2-3-4-4 DICOM Option Pre-installation Requirements To configure the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e to work with other network connections, the site’s network administrator must provide some necessary information. Information must include: • A host name, local port number, AE Title, IP address and Net Mask for the LOGIQ e/LOGIQ e Vet/ LOGIQ i/Vivid e . • The IP addresses for the default gateway and other routers at the site for ROUTING INFORMATION. • The host name, IP address, port and AE Title for each device the site wants connected to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e for DICOM APPLICATION INFORMATION. A field for the make (manufacturer) and the revision of the device, is also included. This information may be useful for solving errors. Chapter 2 Site preparations 2-9

[Page 52] 2-3-4-4 DICOM Option Pre-installation Requirements (cont’d) LOGIQ e/ Host Name Local Port IP Address . . . AE Title Net Mask . . . ROUTING INFORMATION GATEWAY IP Addresses Destination IP Addresses Default . . . ROUTER1 . . . . . . ROUTER2 . . . . . . ROUTER3 . . . . . . DICOM APPLICATION INFORMATION NAME MAKE/REVISION AE TITLE IP ADDRESSES PORT Store 1 . . . Store 2 . . . Store 3 . . . Store 4 . . . Store 5 . . . Store 6 . . . Worklist . . . Storage . . . Commit MPPS . . . Figure 2-2 Worksheet for DICOM Network Information 2-10 Section 2-3 - Facility Needs

[Page 53] Chapter 3 System Setup Section 3-1 Overview 3-1-1 Purpose of Chapter 3 This chapter contains information needed to install the unit. Included are references to a procedure that describes how to receive and unpack the equipment and how to file a damage or loss claim. How to prepare the facility and unit of the actual installation, and how to check and test the unit, probes, and external peripherals for electrical safety are included in this procedure. Also included in this section are guidelines for transporting the unit to a new site. Table 3-1 Contents in Chapter 3 Section Description Page Number 3-1 Overview 3-1 3-2 Receiving and Unpacking the Equipment 3-4 3-3 Packing the Equipment 3-7 3-4 Preparing for Installation 3-8 3-5 Completing the Installation 3-9 3-6 System Configuration 3-12 3-7 Software/Option Configuration 3-27 3-8 Connectivity Installation Worksheet 3-28 3-9 Loading Base Image Software 3-29 3-10 Software Version check out 3-30 3-11 Paperwork 3-31 Chapter 3 System Setup 3-1

[Page 54] 3-1-2 Average Installation Time Table 3-2 Average Installation Time Description Average Installation Time Comments Unpacking the scanner 20 minutes Scanner wo/options 30 minutes Dependent on the configuration that is required DICOM Option 30 minutes Dependent on the amount of configuration The LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e installation and functional checkout will take approximately one hour. LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e consoles with optional equipment may take slightly longer. 3-2 Section 3-1 - Overview

[Page 55] 3-1-3 Installation Warnings 8.) There are no operator serviceable components. To prevent shock, do not remove any covers or panels. Should problems or malfunctions occur, unplug the power cord. Only qualified service personnel should carry out servicing. NOTE: For information regarding packing labels, refer to LABELS ON PACKAGE. 9.) After being transported, the unit may be very cold or hot. If this is the case, allow the unit to acclimate before you turn it on. It requires one hour for each 2.5×C increment it's temperature is below 10×C or above 40×C. DANGER Equipment damage possibility. Turning the system on without acclimation after arriving at site may cause the system to be damaged. Table 3-3 Time for Settlement ° C 60 55 50 45 40 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 -40 ° F 140 131 122 113 104 95 86 77 68 59 50 41 32 23 14 5 -4 -13 -22 -31 -40 hrs 8 6 4 2 0 0 0 0 0 0 0 2 4 6 8 10 12 14 16 18 20 3-1-4 Safety Reminders DANGER WHEN USING ANY TEST INSTRUMENT THAT IS CAPABLE OF OPENING THE AC GROUND LINE (I.E., METER’S GROUND SWITCH IS OPEN), DON’T TOUCH THE UNIT! CAUTION If the unit is very cold or hot, do not turn on its power until it has had a chance to acclimate to its operating environment. DANGER To prevent electrical shock, connect the unit to a properly grounded power outlet. Do not use a three to two prong adapter. This defeats safety grounding. DANGER Do not operate this unit unless all board covers are securely in place. DANGER OPERATOR MANUAL(S) The User Manual(s) should be fully read and understood before operating the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e and kept near the unit for quick reference. DANGER ACOUSTIC OUTPUT HAZARD Although the ultrasound energy transmitted from the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e probe is within FDA limits, avoid unnecessary exposure. Ultrasound energy can produce heat and mechanical damage Chapter 3 System Setup 3-3

[Page 56] Section 3-2 Receiving and Unpacking the Equipment When a new system arrives, check that any components are not damaged and are not in short supply. If shipping damage or shortage occurs, contact the address shown in Chapter 1. 1.) Cut the four PLASTIC BANDs. 2.) Cut the adhesive tape and open top covers of paper carton. Adhesive tape Plastic Bands Figure 3-1 Open top covers of paper carton. 3-4 Section 3-2 - Receiving and Unpacking the Equipment

[Page 57] 3.) Take out the Paper pad. 4.) Take out console together with 2 interleavers from console package. 5.) Take out the interleavers beside Accessories Package. 6.) Take out Accessories Package. Paper Pad Console and interleavers Console Package Accessories Package Figure 3-2 Unpacking the equipment CAUTION Do not lift the unit by the rubber band. Equipment damage may result. Chapter 3 System Setup 3-5

[Page 58] 7.) Remove 2 interleavers. 8.) Remove plastic bag. Interleaver Console Interleaver Figure 3-3 Removing interleavers and plastic bag 3-6 Section 3-2 - Receiving and Unpacking the Equipment

[Page 59] NOTE: Check the shipping container for special instructions. Verify that the container is intact. In some cases a secondary container may be used. If so, ask the carrier for unpacking instructions. Figure 3-4 Labels on Package CAUTION Please carefully unpack the system, and do not dispose the package of LOGIQ e/LOGIQ e Vet/ LOGIQ i/Vivid e , so that it can be reused for service. 3-2-1 Moving into Position CAUTION Do not lift the unit by the rubber band. Use handle to move system. CAUTION Equipment Damage Possibility. Lifting the console by holding covers may damage the covers. Do not lift the console by holding any covers. In general, a single adult can move the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . Before moving, store all loose parts in original accessory box or in back pack. Return probes to original box. Section 3-3 Packing the Equipment Please pack LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e in the reverse order of unpacking. Chapter 3 System Setup 3-7

[Page 60] Section 3-4 Preparing for Installation 3-4-1 Verify Customer Order Compare items received by the customer to that which is listed on the delivery order. Report any items that are missing, back ordered or damaged. 3-4-2 Physical Inspection 3-4-2-1 System Voltage Settings • Verify that the scanner is set to the correct voltage. The Voltage settings for the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Scanner is found on a label located on the AC adapter. • 220-240VAC(China); 100-120VAC(USA/Japan); 220-240VAC(Europe, Latin America). WARNING WARNING Connecting a LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e scanner to the wrong voltage level will most likely destroy the scanner. 3-4-3 EMI Protection This Unit has been designed to minimize the effects of Electro Magnetic Interference (EMI). Many of the covers, shields, and screws are provided primarily to protect the system from image artifacts caused by this interference. For this reason, it is imperative that all covers and hardware are installed and secured before the unit is put into operation. 3-8 Section 3-4 - Preparing for Installation

[Page 61] Section 3-5 Completing the Installation 3-5-1 Power On / Boot Up NOTE: After turning off a system, wait at least ten seconds before turning it on again. The system may not be able to boot if power is recycled too quickly. 3-5-1-1 Scanner Power On Lower the handle. Plug the AC adapter output connector into the system DC input port (located on the system’s rear panel) with the arrow side upward. Plug the AC adapter power cord into a grounded, protective earth outlet. UP UP Figure 3-5 Connect AC adapter When power is applied to the scanner, power is distributed to the Cooling Unit, Control Panel, LCD, Peripherals and the Back-end Processor. Chapter 3 System Setup 3-9

[Page 62] 3-5-1-2 Turn on the system Press the Power On/Off switch at the front of the system once. Power On/Off switch Figure 3-6 Power On/Off Switch When the Power On/Off switch on the Control Panel is pressed once, the Back-end Processor starts and the software code is distributed to initiate the scanner. No status messages are displayed during this process. 3-5-2 Power Off/ Shutdown NOTE: After turning off a system, wait at least ten seconds before turning it on again. The system may not be able to boot if power is recycled too quickly. 3-5-2-1 Back-end Processor Power Down To power down the system: 1.) Press the Power On/Off switch at the front of the system once. 2.) The System-Exit window is displayed. Figure 3-7 System Exit Window 3.) Using the Trackball or Select key, select Shutdown. 4.) The shutdown process takes a few seconds and is complete when the power status LED is turned off. 5.) Disconnect the probes.Clean or disinfect all probes as necessary. Store them in their shipping cases to avoid damage. 6.) Close LCD cover. 3-10 Section 3-5 - Completing the Installation

[Page 63] 3-5-2-2 Scanner Shutdown Disconnect the Mains Power Cable if necessary. For example: Relocating the scanner. 3-5-3 Transducer Connection 1.) Carefully open the system LCD display, plug the probe connector into the probe port, then lock the probe latch upward. NOTE: Please ensure that the probe latch is in an unlocked position before you connect the probe to the system. Probe Latch Figure 3-8 Connect the probe NOTE: It is not necessary to turn OFF power to connect or disconnect a probe. Chapter 3 System Setup 3-11

[Page 64] Section 3-6 System Configuration 3-6-1 System Specifications 3-6-1-1 Physical Dimensions The physical dimensions of the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e console are summarized in Figure 3-9 on page 3-12 . Table 3-4 Physical Dimensions of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Height Width Depth Unit Console Console Console Console Console with Only with handle Only with handle Console Only handle Unit 61 100 340 375 287 337 mm 2.4 3.9 13.4 14.8 11.3 13.3 inches WEIGHT: 4.6KG NOTE: Length is in mm Figure 3-9 Overall Dimensions 3-6-2 Electrical Specifications Table 3-5 Electrical Specifications for LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Adapter Voltage Tolerances Current Frequency TWADP100 100-240 VAC +/-10% 1.3A (max) 50/60Hz 3-12 Section 3-6 - System Configuration

[Page 65] 3-6-3 Approved peripherals Table 3-6 Approved on-board peripherals Device Manufacturer Model Interface Remark B/W Printer SONY UP-D897 USB SONY UP-D23MD USB Digital Color Printer SONY UP-D25MD USB HP HP Officejet Pro K5400 USB HP Color Printer HP HP Officejet Pro K8600 USB HP HP Deskjet 470 USB LITEON LITEON DX-20A4P USB DVD-RW LITEON LITEON Model eHAU 120 USB LITEON LITEON Model eHAU 324 USB NetGear WN111V2 USB Wireless Lan Adapter NetGear WG111V3 USB Linksys Linksys WUSB54G USB 3-pedal footswitch Steute MKF 2-MED GP26 USB 1-pedal footswitch Whanam FSU2001 USB 1-pedal footswitch Whanam FSU-1000 USB SanDisk CRUZER 2G USB SanDisk CRUZER 4G USB USB Memory CRUZER 4G with U3 Only supported by LOGIQ e R6.x.x SanDisk USB Application and LOGIQ e R7.x.x. Shenzhen Gaojian HE 702A USB USB HUB Shenzhen Gaojian HE420GE USB ECG NORAV ECG-USB1 USB Seagate USB HDD 80G USB USB HDD Seagate USB HDD 250G USB Seagate USB HDD 500G USB MD-800E Not supported by LOGIQ e R4.x.x, DVD-Recorder Panasonic MD-800U USB LOGIQ e R6.x.x, Vivid e R4.x.x, LOGIQ i R4.x.x Pinnacle Video Transfer - Not supported by LOGIQ e R5.0.x, Video Transfer Pinnacle 8230-10022-11 USB LOGIQ e Vet R5.0.x, Vivid e R5.0.x, LOGIQ i R5.0.x Handheld Handheld 3800G USB Only supported by LOGIQ e R5.2.x, BarCode Reader* R6.x.x, R7.x.x, LOGIQ e Vet 6.x.x Handheld Handheld 4600G USB NOTE: For detailed installation information and connection procedures, please refer to Peripheral Installation manual. NOTE: BarCode Reader* is supported by LOGIQ e Software version R5.2.x, R6.x.x only. Chapter 3 System Setup 3-13

[Page 66] 3-6-4 Connecting Cables WARNING WARNING Equipment damage possibility. Be sure to use the following recommended connecting cables to connect recording devices and a network with LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e console. Table 3-7 List of Connecting Cables Name Part No. Figure NOTE USB Cable 5122305 For USB Printer & USB DVD-RW 3-6-5 Peripherals/Accessories Connector Panel LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e peripherals and accessories can be properly connected using the side connector panel. 3-6-5-1 Rear Panel Connector Located on the rear panel are video input and output connectors, power connector and ethernet port. 1 2 3 Figure 3-10 Rear Connector Panel 1.) Port for DC input (AC Adapter) 2.) Docking Connector 3.) SVGA Output 4.) Ethernet port 3-14 Section 3-6 - System Configuration

[Page 67] 3-6-5-2 Left Panel Connector Located on the left side panel are two USB Ports for control connections for printer, service tools and earphone port. Figure 3-11 Left Side Panel 1.) Two interchangeable USB Port (Digital Printers, DVD-RW and/or FootSwitch, etc) 2.) Earphone Port. NOTE: Each outer (case) ground line of peripheral/accessory connectors are protectively grounded. Signal ground lines are not isolated. Chapter 3 System Setup 3-15

[Page 68] 3-6-5-3 This section indicates the pin assignment for each connector. 1. Pin Assignment of DC input Connector: 4 Pin, Female Table 3-8 Pin Assignments of DC input Pin No. Signal Pin No. Signal 1 +20V 3 GND 2 +20V 4 GND 2. Pin Assignment of USB Table 3-9 Pin assignment of USB1 Pin No. Signal Pin No. Signal 1 +5VDC 3 DATA+ 2 DATA- 4 GND Table 3-10 Pin assignment of USB2 Pin No. Signal Pin No. Signal 1 +5VDC 3 DATA+ 2 DATA- 4 GND 3. Pin assignment of RS232C for external VGA Connector: D-SUB, 15Pin, Female Table 3-11 Pin Assignments of RS232C for External VGA Pin No. Signal Pin No. Signal 1 RED 9 N/A 2 GREEN 10 SGND 3 BLUE 11 N/A 4 N/A 12 N/A 5 GND 13 HSYNC 6 RGND 14 VSYNC 7 GGND 15 N/A 8 BGND 16 3-16 Section 3-6 - System Configuration

[Page 69] 3-6-5-4 Connect peripherals A.) Connect B/W printer to the system. B/W Printer can be properly connected using USB Port1 or USB Port 2 (Figure 3-12 on page 3-17 ). Figure 3-12 Connect B/W printer to the system B.) Connect UP-D23MD color printer to the system. UP-D23MD Color Printer can be properly connected using USB Port1 or USB Port 2 (Figure 3-13 on page 3-17 ). Figure 3-13 Connect digital color printer to the system NOTICE HP Deskjet 470 /HP Officejet Pro K5400 Color Printer must connect with PIT (Printer Isolation Transformer) when being used. Chapter 3 System Setup 3-17

[Page 70] C.) Connect DVD-RW to the system. DVD-RW can be properly connected using USB Port1 or USB Port2 (Figure 3-14 on page 3-18 ). Figure 3-14 Connect DVD-RW to the system CAUTION DO NOT connect DVD-RW to the system while scanning. LITEON DVD-RW drive recommended media list Media issues are common throughout the DVD-RW drive industry. Because DVD media vendors often change disc suppliers, quality levels may change due to manufacturing differences. This means that you may encounter DVD/CD creation problems with media that may have worked successfully before. Overall system configuration and other factors may also affect the success of creating a DVD/CD. The following media types have been tested. LITEON highly recommends that you use the media types on this list when creating your DVDs/CDs. Not all brands of media have been tested and, therefore, you may encounter success with other brands not listed. This list will be updated as other media is tested and approved. Table 3-12 LITEON DVD-RW drive recommended media list Brand Name Type SONY DVD-R SONY CD-R SONY DVD-RW Mitsubishi CD-R Mitsubishi CD-RW Mitsubishi DVD-R Mitsubishi DVD-RW JVC DVD-R MBI CD-R MBI DVD-R Taiyo Yuden CD-R Taiyo Yuden DVD-R 3-18 Section 3-6 - System Configuration

[Page 71] D.) Connect FootSwitch to the system. FootSwitch can be properly connected using USB Port1 or USB Port2. 1-pedal footswitch 3-pedal footswitch Figure 3-15 Connect Foot Switch to the system E.) Connect Wireless LAN Adapter to the system. Wireless LAN Adapter can be properly connected using USB port. Wireless Lan Adapter Figure 3-16 Connect Wireless LAN Adapter to the system F.) Connect the CRT to the system. CRT can be properly connected using the SVGA output. Chapter 3 System Setup 3-19

[Page 72] G.) Connect the USB Memory to the system. The USB Memory can be properly connected using USB port 1 or 2. Figure 3-17 USB Memory Connection H.) Connect the ECG to the system. ECG can be properly connected using USB port 1 or 2. Figure 3-18 ECG 3-20 Section 3-6 - System Configuration

[Page 73] I.) Connect the USB HDD to the system. The USB Harddisk can be properly connected using USB port 1 and 2. Figure 3-19 Emergency Disk Connection J.) Connect the BarCode Reader to the system, the BarCode Reader can be properly connected via USB port 1 or 2. Figure 3-20 BarCode Reader Connection Chapter 3 System Setup 3-21

[Page 74] K.) Connect the Sandisk U3 USB Flash Drive to the system. The Sandisk U3 USB Flash Drive can be properly connected using USB port 1 and 2. Figure 3-21 Sandisk U3 USB Flash Drive Connection NOTE: The Password of the Sandisk U3 USB Flash Drive is Predefined. NOTE: The Sandisk U3 USB Flash Drive is only available on LOGIQ e R6.x.x and LOGIQ e R7.x.x. Connect the security enabled Sandisk U3 USB Flash Drive into the system, input the password in the pop-up dialog. Click OK to login, click Cancel to cancel. Figure 3-22 Input the password The Sandisk U3 USB Flash Drive can be used if the right password is entered. An error message will display if the wrong password is entered. 3-22 Section 3-6 - System Configuration

[Page 75] Figure 3-23 Wrong password error Click OK , input the password again. The Sandisk U3 USB Flash Drive will be locked if reaching the maximum number of failed password attempts. Figure 3-24 Sandisk U3 USB Flash Drive locked NOTE: Please refer to the operation manual of each peripheral for information needed by the user to operate the system safely. For detailed installation information, please refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Peripheral Installation Instruction manual. Chapter 3 System Setup 3-23

[Page 76] L.) Connect the external monitor to the system. The monitor can be properly connected using the VGA port. Figure 3-25 VGA Connection Press Ctrl+Alt+V on the keyboard, a dialog box appears. For LOGIQ e R5.x.x, R6.x.x, R7.x.x, LOGIQ i R5.x.x, For LOGIQ e R4.x.x, LOGIQ i R4.x.x, Vivid e R4.x.x Vivid e R5.x.x/R6.x.x Figure 3-26 Graphics Controller Properties Select Intel(R) Dual Display Clone; check the Same display configuration driver on both display box and select OK. NOTE: Please refer to the operation manual of each peripheral for information needed by the user to operate the system safely. NOTE: For LOGIQ e R5.2.x, R6.x.x, R7.x.x, the default set is dual, it will not pop up Figure 3-26. For detailed installation information, please refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Peripheral Installation manual. 3-24 Section 3-6 - System Configuration

[Page 77] 3-6-6 Available Probes See in specification in the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e User Reference Manual for Probes and intended use. For LOGIQ e R4.0.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS Probes. For LOGIQ e R5.0.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS, i/t739-RS, 9L-RS Probes. For LOGIQ e R5.2.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS, i/t739-RS, 9L-RS, 16L-RS Probes. For LOGIQ e R6.x.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS, i/t739-RS, 9L-RS, 16L-RS, 6Tc-RS, 6S-RS Probes. For LOGIQ e R7.x.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS, i/t739-RS, 9L-RS, 16L-RS, 6Tc-RS, 6S-RS, L8-18i-RS,P2D Probes. For LOGIQ i R4.x.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 12L-RS Probes. For LOGIQ i R5.x.x, the system supports 4C-RS, E8C-RS, 8C-RS, i12L-RS, 8L-RS, 3S-RS, 6S-RS, 12L-RS, i/t739-RS, P2D, 9L-RS Probes. For Vivid e R4.x.x, the system supports 4C-RS, i12L-RS, 8L-RS, 3S-RS Probes. For Vivid e R5.0.x, the system supports 4C-RS, i12L-RS, 8L-RS, 3S-RS, 8C-RS, 9L-RS, P2D Probes. For Vivid e R5.2.x, the system supports 4C-RS, 8C-RS, E8C-RS, 8L-RS, 9L-RS, 12L-RS, i12L-RS, 3S- RS, 6S-RS, P2D Probes . For Vivid e R6.x.x, the system supports 4C-RS, 8C-RS, E8C-RS, 8L-RS, 9L-RS, 12L-RS, i12L-RS, 3S- RS, 6S-RS, P2D, 6Tc-RS Probes. For LOGIQ e Vet R5.0.x, the system supports 4C-RS Vet, E8C-RS Vet, 8C-RS Vet, i12L-RS Vet, 8L- RS Vet, 3S-RS Vet, 12L-RS Vet, 9L-RS Vet, i739-RS LC, 6S Vet-RS For LOGIQ e Vet R5.2.x, the system supports 4C-RS Vet, E8C-RS Vet, 8C-RS Vet, i12L-RS Vet, 8L- RS Vet, 3S-RS Vet, 12L-RS Vet, 9L-RS Vet For LOGIQ e Vet R6.x.x, the system supports 4C-RS Vet, E8C-RS Vet, 8C-RS Vet, i12L-RS Vet, 8L- RS Vet, 3S-RS Vet, 12L-RS Vet, 9L-RS Vet, 6S Vet-RS, i739-RS-LC, 6Tc-RS Vet NOTE: 16L-RS is not available in China. Chapter 3 System Setup 3-25

[Page 78] 3-6-6 Available Probes (cont’d) Table 3-13 List of Probes for LOGIQ e/LOGIQ i/Vivid e Probe Name Material of Headshell Area of Using TYPE Catalog Number Part Number 4C-RS NORYL GENERAL PURPOSE CONVEX H4000SR 5131629 E8C-RS VALOX TRANSVAGINAL TRANSRECTAL MICRO-CONVEX H40402LN 2290777 VETERINARY 8C-RS VALOX MICRO-CONVEX H40402LS 2354971 PEDIATRIC NEONATAL INTRAOPERATIVE SMALL PARTS i12L-RS ABS (GE) LINEAR H40402LW 2377942 VASCULAR PEDIATRICS SMALL PARTS 8L-RS VALOX LINEAR H40402LT 2376127 PERIPHERAL VASCULAR CARDIOLOGY 3S-RS VALOX SECTOR H4000PD 2355686 TRANSVAGINAL ABDOMEN SMALL PARTS 12L-RS NORYL LINEAR H40402LY 5154514 PERIPHERAL VASCULAR 9L-RS VALOX SMALL PATS VASCULAR LINEAR H40442LL 5213143 i739-RS VALOX INTRAOPERATIVE LINEAR H40402LJ 2404995 t739-RS VALOX INTRAOPERATIVE LINEAR H40412LP 2404999 P2D CARDIOLOGY Non-Imaging CW H45551CA KE100003 6S-RS VALOX CARDIOLOGY PEDIATRICS SECTOR H45021RP 47236956 SMALL PARTS 16L-RS VALOX LINEAR H40452LJ 5317271 PERIPHERAL VASCULAR 6Tc-RS VALOX TRANSESOPHAGEAL FOR ADULT SECTOR H45551ZE KN100104 NOTE: 16L-RS is not available in China. 3-26 Section 3-6 - System Configuration

[Page 79] 3-6-6 Available Probes (cont’d) Table 3-14 List of Probes for LOGIQ e Vet Probe Name Material of Headshell Area of Using TYPE Catalog Number Part Number 4C-RS Vet NORYL GENERAL PURPOSE CONVEX H40442LY 5198378 TRANSVAGINAL E8C-RS Vet VALOX MICRO-CONVEX H41562LL 5134643 TRANSRECTAL VETERINARY 8C-RS Vet VALOX PEDIATRIC MICRO-CONVEX H41562LK 5134642 NEONATAL INTRAOPERATIVE SMALL i12L-RS Vet ABS (GE) PARTS VASCULAR LINEAR H41562LN 5134645 PEDIATRICS SMALL PARTS 8L-RS Vet VALOX LINEAR H41562LM 5134644 PERIPHERAL VASCULAR CARDIOLOGY 3S-RS Vet VALOX TRANSVAGINAL SECTOR H41562LR 5134647 ABDOMEN SMALL PARTS 12L-RS Vet NORYL LINEAR H40442LZ 5212304 PERIPHERAL VASCULAR 9L-RS Vet VALOX SMALL PARTS VASCULAR LINEAR H40442LW 5220453 i739-RS-LC VALOX INTRAOPERATIVE LINEAR H41482LS 5136420 CARDIOLOGY 6SVet-RS VALOX SECTOR H40452L 5198571 PEDIATRICS TRANSVAGINAL FOR 6Tc-RS Vet VALOX SECTOR H48922LB 5430790 ADULT NOTE: i739-RS-LC , 6SVet-RS and 6Tc-RS Vet probes are only availble for R6.x.x. Section 3-7 Software/Option Configuration Refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Basic User Manual, Chapter 16, Customizing Your System for information on configuring items like Hospital, Department, Language, Units (of measure), Date, Time and Date Format. For information on configuring Software Options, Refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Basic User Manual, Chapter 16, Customizing Your System. For information on configuring DICOM Connectivity, Refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Basic User Manual, Chapter 16, Customizing Your System. Chapter 3 System Setup 3-27

[Page 80] Section 3-8 Connectivity Installation Worksheet Site System Information Floor: Comments: Site: Dept: Room: LOGIQ SN: Type: REV: CONTACT INFORMATION Name Title Phone E-Mail Address TCP/IP Settings Name - AE Title: IP Settings Remote Archive Setup IP Address: Remote Archive IP: Subnet Mask: Remote Archive Name: Default Gateway: Services (Destination Devices) Device Type Manufacturer Name IP Address Port AE Title 3-28 Section 3-8 - Connectivity Installation Worksheet

[Page 81] Section 3-9 Loading Base Image Software This information has been moved, please refer to: Section 8-3 "Loading Base Image Software" on page 8-4 Chapter 3 System Setup 3-29

[Page 82] Section 3-10Software Version check out 3-10-1 Functional Check-out 1.) Power on LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e scanner and wait until system booting to main screen. 2.) Press Utility/Config key on control panel. 3.) Choose the About button on the right. Figure 3-27 About 4.) Check whether "Software version" is the right version for use. Figure 3-28 Software version 3-30 Section 3-10 - Software Version check out

[Page 83] Section 3-11 Paperwork NOTE: During and after installation, the documentation (i.e. User Manuals, Installation Manuals...) for the peripheral units must be kept as part of the original system documentation. This will ensure that all relevant safety and user information is available during the operation and service of the complete system. 3-11-1 Product Locator Installation NOTE: The Product Locator Installation Card shown may not be same as the provided Product Locator card. Figure 3-29 Product Locator Installation Card 3-11-2 User Manual(s) User Check that the correct User Manual(s) for the system and software revision, is included with the installation. Specific language versions of the User Manual may also be available. Check with your GE Sales Representative for availability. Chapter 3 System Setup 3-31

[Page 84] This page was intentionally left blank. 3-32 Section 3-11 - Paperwork

[Page 85] Chapter 4 Functional Checks Section 4-1 Overview 4-1-1 Purpose for Chapter 4 This chapter provides procedures for quickly checking major functions of the LOGIQ e/LOGIQ e Vet/ LOGIQ i/Vivid e console, diagnostics by using the built-in service software, and power supply adjustments. Table 4-1 Contents in chapter 4 Section Description Page Number 4-1 Overview 4-1 4-2 Required Equipment 4-1 4-3 General Procedure 4-2 4-4 Software Configuration Checks 4-37 4-5 Peripheral Checks 4-37 Section 4-2 Required Equipment To perform these tests, you'll need any of the sector, linear, or convex transducers. (normally you should check all the transducers used on the system) Chapter 4 Functional Checks 4-1

[Page 86] Section 4-3 General Procedure CAUTION SYSTEM REQUIRES ALL COVERS Operate this unit only when all board covers and frame panels are securely in place. The covers are required for safe operation, good system performance and cooling purposes. NOTICE Lockout/Tagout Requirements (For USA only) Follow OSHA Lockout/Tagout requirements by ensuring you are in total control of the Power Cable on the system. TAG LOCKOUT Signed Date 4-3-1 Power On/Boot Up After AC/DC is connected correctly to the scanner, the power is applied to the scanner. When the Control panel Power On/Off key is pressed once, the System starts. 4-3-1-1 Scanner Power On Lower the handle. Plug the AC adapter output connector into the system DC input port (located on the system’s rear panel) with the arrow side upward. Plug the AC adapter power cord into a grounded, protective earth outlet. UP UP Figure 4-30 connect AC adapter 4-2 Section 4-3 - General Procedure

[Page 87] 4-3-1-1 Scanner Power On (cont’d) When power is applied to the scanner, power is distributed to the Cooling Unit, Control Panel, LCD, Peripherals and the Back-end Processor. 4-3-1-2 Turn on the system Press the Power On/Off switch at the front of the system once. Power On/Off switch Figure 4-31 Power On/Off Switch When the Power On/Off switch on the Control Panel is pressed once, the Back-end Processor starts and the software code is distributed to initiate the scanner. No status messages are displayed during this process. 4-3-2 Power Off/ Shutdown NOTE: After turning off a system, wait at least ten seconds before turning it on again. The system may not be able to boot if power is recycled too quickly. 4-3-2-1 Back-end Processor Power Down To power down the system: 1.) Press the Power On/Off switch at the front of the system once. 2.) The System-Exit window is displayed. Figure 4-1 System Exit Window 3.) Using the Trackball or Select key, select Shutdown. Chapter 4 Functional Checks 4-3

[Page 88] 4-3-2-1 Back-end Processor Power Down (cont’d) 4.) The shutdown process takes 15 seconds and the power off sequence is complete when the power status LED is turned off. 5.) Disconnect the probes.Clean or disinfect all probes as necessary. Store them in their shipping cases to avoid damage. 6.) Close LCD cover. 4-3-2-2 Scanner Shutdown Disconnect the Mains Power Cable is necessary. For example: Relocating the scanner. CAUTION DO NOT unplug and/or transport the unit until after the power off sequence has been completed. Failure to do so may result in corrupted patient files. 4-3-2-3 Full Maintenance Reboot Full Maintenance Reboot will fully restart the whole system for performance improvement. NOTE: It’s recommended to do Full Maintenance Reboot at least daily or when system starts to slow down or lag in its reaction. 1.) Press the Power On/Off switch at the front of the system once. 2.) Click “Full Maintenance Reboot”. 3.) Full Maintenance Reboot dialog is displayed. Figure 4-2 “Full Maintenance Reboot” dialog 4-3-2-4 Exit (only activated for LOGIQ e R6.0.2) Exit will reboot application. 1.) Press the Power On/Off switch at the front of the system once. 2.) Click “Exit”. 3.) The application will reboot. 4-4 Section 4-3 - General Procedure

[Page 89] 4-3-3 Archiving and Loading Presets NOTE: Always save presets before any software reload. This ensures the presets loaded after the software reload are as up–to–date as possible. All user presets except changes to Summary, Anatomy, and Biometry pages, can be saved on an DVD- R disk (or USB memory device) for reloading on the system. NOTICE Presets should NOT be saved on the same DVD-R disk (or USB memory device) as images. The Archive Menu lists the images but does NOT list the presets stored on a DVD-R disk (or USB memory device). 4-3-3-1 Archiving Presets to an DVD-R Disk (or USB memory device) 1.) Insert an empty (blank) DVD-R disk into the DVD-RW. 2.) Access to the Utility/Config Menu, and select System. The Backup sheet will be shown on the LCD display. Figure 4-3 Backup Sheet 3.) Select the item to Backup/Restore. 4.) Enter backup destination or browse through the disk to locate the destination. 5.) Select Backup now. The backup status for each item is displayed on the Result column. Chapter 4 Functional Checks 4-5

[Page 90] 4-3-3-2 Loading Presets from an DVD-R disk (or USB memory device) 1.) Insert the DVD-R disk with the archived Presets into the DVD-RW. 2.) Access to the Utility/Config Menu, and select System. The Restore sheet will be shown on the LCD display. (see Figure 4-3 on page 4-5 ) 3.) Select the item to restore either from Resource Files. 4.) Enter restore destination or browse through the disk to locate the destination. 5.) Select Restore. The restore status for each item is displayed on the Result column. 4-3-4 Adjusting the Display Monitor Please refer to Section 6-2 "Monitor Adjustments" on page 6-2. 4-3-5 Lockout/Tagout (LOTO) requirements Follow OSHA Lockout/Tagout requirements (USA) or local Lockout/Tagout requirements by ensuring you are in total control of the AC power plug at all times during the service process. To apply Lockout/Tagout: 1.) Plan and prepare for shutdown. 2.) Shutdown the equipment. 3.) Isolate the equipment. 4.) Apply Lockout/Tagout Devices. 5.) Remove battery. 6.) Control all stored and residual energy. 7.) Verify isolation. All potentially hazardous stored or residual energy is relieved. NOTICE Energy Control and Power Lockout for LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e WHEN SERVICING PARTS OF THE SYSTEM WHERE THERE IS EXPOSURE TO VOLTAGE GREATER THAN 30 VOLTS: 1. TURN OFF THE SCANNER. 2. UNPLUG THE SYSTEM. 3. MAINTAIN CONTROL OF THE SYSTEM POWER PLUG. 4. WAIT FOR AT LEAST 20 SECONDS FOR CAPACITORS TO DISCHARGE AS THERE ARE NO TAG & TEST POINTS TO VERIFY ISOLATION. THE AMBER LIGHT ON THE OP PANEL ON/OFF BUTTON LOCKOUT WILL TURN OFF. Signed Date 5. REMOVE THE SYSTEM BATTERY. 4-6 Section 4-3 - General Procedure

[Page 91] 4-3-6 System Features 4-3-6-1 Control Panel 5 3 Figure 4-4 Control Panel Tour 1.) TGC 2.) New Patient 3.) End Exam 4.) Mode/Gain/Auto Keys 5.) Preset Key 6.) Imaging/Measurement Keys 7.) Depth/Zoom/Ellipse 8.) Image Keys 9.) Print Keys 10.)Freeze 11.)Keyboard Chapter 4 Functional Checks 4-7

[Page 92] 4-3-6-2 LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e SoftMenu Key Tour In general, there are two types of softMenu keys: Paddle Switch and adjustable knobs. Figure 4-5 SoftMenu Key Tour 1.) The Paddle Switch is used to access and adjust the Sub SoftMenu. 2.) Press the adjustable knobs to toggle option menu between line one and line two. 3.) Rotate the adjustable knobs to adjust the corresponding parameters. 4-8 Section 4-3 - General Procedure

[Page 93] 4-3-6-3 Monitor Display 1 2 3 6 13 20 21 19 22 23 24 Figure 4-6 Monitor Display Tour Table 4-2 Monitor Display Features 1. Institution/Hospital Name, Date, Time, Operator 13. Imaging Parameters by Mode (current mode highlighted). Identification, system status (real-time of frozen). 2. Patient Name, Patient Identification. 14. Focal Zone. 3. Acoustic Output Readout, 15. TGC (not shown on the image). 4. GE Symbol: Probe Orientation Marker. Coincides with a 16. Body Pattern. probe orientation marking on the probe. 5. Image Preview. 17. Depth Scale. 6. Gray/Color Bar. 18. SoftMenu 7. Cine Gauge. 19. Caps Lock: On/Off. 8. Measurement Summary Window. 20. Start menu icon. 9. Image. 21. Battery icon. 10. Measurement. 22. Network icon. 11. Results Window. 23. Trackball Functionality Status: Scroll, M&A (Measurement and Analysis), Position, Size, Scan Area Width and Tilt. 12. Probe Identifier. Exam Study. 24. Active key for Depth/Zoom/Ellipse Chapter 4 Functional Checks 4-9

[Page 94] 4-3-7 B Mode Checks 4-3-7-1 Preparations 1.) Connect one of the probes listed in 3-6-6 "Available Probes" on page 3-25, in Chapter 3 Installation to the System probe connector. 2.) Turn ON the scanner (if it isn’t turned on already) NOTE: The keyboard layout varies from each Product, the following figures show LOGIQ e R5.x.x as an example. SoftMenu Key Primary Menu Secondary Menu Zoom / Depth B Mode Scan Area Freeze Figure 4-7 Controls available in B Mode Figure 4-8 B Mode Screen Picture Example 4-10 Section 4-3 - General Procedure

[Page 95] 4-3-7-2 B Mode OP Panel Controls Table 4-3 B Mode Control Panel Controls 1 Press B Mode key B Mode Starts Adjust the field of view. Increasing the depth may view larger/deeper structures rates, and decreasing the depth may view near the skin 2 Adjust Depth line.Press Up/Down Button to increase/ decrease. Depth displays on the monitor in cm. Controls the amount of echo information displayed in an image. Turn B Mode dial to 3 Adjust Gain the left/right to increase/decrease Gain. Gain displays on the monitor in Gn (dB). Increases the number of focal zones or moves the focal zone(s) to tighten up the beam for specific area. Press the control to 4 Adjust Focus toggle between Focus Position and Focus Number. Press Up/Down Button to move or adjust the focal numbers. Optimize the image based upon a specified region of interest or anatomy. Press the 5 Activate Auto Optimize Center Button in the Gain Dial to toggle the ATO/ACE On and Off. Amplifies the returning signals to correct for the attenuation caused by tissues at increasing depth. TGC slide pots spaced 7 Adjust Time Gain Compensation (TGC) proportional to the depth. Move the slide pots to the left/right to decrease/increase TGC. A TGC curve appears on the display. Widen or narrow the size of the sector angle to maximize the image’s region of interest 8 Adjust Scan Area (ROI). Press Scan Area and move the Trackball to narrow/widen the angle. Changes the location of the focal point(s). A 9 Adjust Zoom triangular focus marker indicates the depth of the focal point. Toggles the left/right orientation of the scan 10 Reverse image. Chapter 4 Functional Checks 4-11

[Page 96] 4-3-7-3 B Mode Softmenu Key Table 4-4 B Mode Softmenu Key Step Task Expected Result(s) comments Selects a level below which echoes will not be 1 Adjust Rejection amplified (an echo must have a certain minimum amplitude before it will be processed). Enables gray scale image colorization. To 2 Activate Colorize deactivate, reselect a Gray Map. Edge Enhance brings out subtle tissue differences and boundaries by enhancing the For LOGIQ e, LOGIQ e Vet and Adjust Edge Enhance gray scale differences corresponding to the LOGIQ i edges of structures. Adjustments to M Mode's edge enhancement affects the M Mode only. Edge Enhance brings out subtle tissue differences and boundaries by enhancing the Adjust Edge Enhance/Contour gray scale differences corresponding to the For Vivid e edges of structures. Adjustments to M Mode's edge enhancement affects the M Mode only. Determines how the echo intensity levels 4 Activate Gray Map received are presented as shades of gray. Multi Frequency mode lets you downshift to the 5 Adjust Frequency probe's next lower frequency or shift up to a higher frequency. Temporal filter that averages frames together. For LOGIQ e, LOGIQ e Vet and Adjust Frame Average This has the effect of presenting a smoother, LOGIQ i softer image. Temporal filter that averages frames together. Adjust DDP This has the effect of presenting a smoother, For Vivid e softer image. Rotates the image by selecting the value from 7 Adjust Rotation the pop-up menu. Optimizes B Mode frame rate or spatial For LOGIQ e, LOGIQ e Vet and Adjust Line Density resolution for the best possible image. LOGIQ i Optimizes B Mode frame rate or spatial Adjust Frame Rate For Vivid e resolution for the best possible image. Optimizes image quality and allows user to 9 Power output reduce beam intensity. 2% increments between 0-100%. Values greater than 0.1 are displayed. Dynamic Range controls how echo intensities 10 Dynamic Range are converted to shades of gray, thereby increasing the adjustable range of contrast. Increases the number of transmit focal zones or moves the focal zone(s) so that you can tighten 11 Focus Number and Position up the beam for a specific area. A graphic caret corresponding to the focal zone position(s) appears on the right edge of the image. 12 Virtual Convex Virtual Convex for linear probe Only for LOGIQ e R5.x.x/R6.x.x/ 13 Virtual Apex Virtual Convex for Sector probe R7.x.x, LOGIQ e Vet, LOGIQ i R5.x.x, Vivid e R5.x.x, Vivid e R6.x.x 4-12 Section 4-3 - General Procedure

[Page 97] 4-3-8 M Mode Controls 4-3-8-1 Preparations 1.) Connect one of the probes listed in 3-6-6 "Available Probes" on page 3-25, in Chapter 3 Installation to the System probe connector. 2.) Turn ON the scanner (if it isn’t turned on already). Primary Menu Secondary Menu Gain M/D Cursor M Mode Figure 4-9 Controls available in M Mode Figure 4-10 M Mode Screen Picture Example Chapter 4 Functional Checks 4-13

[Page 98] 4-3-8-2 M Mode OP Panel Controls Table 4-5 M Mode OP Panel Controls 1 Press M Mode key M Mode Starts Controls the amount of echo information displayed in an image. Turn B Mode dial to 2 Adjust Gain the left/right to increase/decrease Gain. Gain displays on the monitor in Gn (dB). Displays the M-Mode cursor on the B-Mode 3 Display M-Mode Cursor image. Press Cursor and Trackball to position M-Mode Cursor. 4-14 Section 4-3 - General Procedure

[Page 99] 4-3-8-3 M Mode Softmenu Key Table 4-6 M Mode Softmenu Key Selects a level below which echoes will not be amplified (an echo must have a certain 1 Adjust Rejection minimum amplitude before it will be processed). Changes the speed at which the time line is 2 Adjust Sweep Speed swept. The following speed values are available, 1, 2, 3, 4, 6, 8, 12, 16. Edge Enhance brings out subtle tissue differences and boundaries by enhancing the For LOGIQ e, LOGIQ Adjust Edge Enhance gray scale differences corresponding to the e Vet and LOGIQ i edges of structures. Adjustments to M Mode's edge enhancement affects the M Mode only. Edge Enhance brings out subtle tissue differences and boundaries by enhancing the Adjust Edge Enhance/Contour gray scale differences corresponding to the For Vivid e edges of structures. Adjustments to M Mode's edge enhancement affects the M Mode only. Determines how the echo intensity levels 4 Activate Gray Map received are presented as shades of gray. Enables gray scale image colorization. To 6 Activate Colorize deactivate, reselect a Gray Map. Displays only timeline screen. Press the Full 7 Activate Full Timeline Timescreen to activate. Select the format to display B image and M For LOGIQ e, LOGIQ Select Display Format image on the LCD. Press Display Format, e Vet and LOGIQ i and select from the pop up menu. Select the Layout to display B image and M Select Layout image on the LCD. Press Display Format, For Vivid e and select from the pop up menu. Dynamic Range controls how echo intensities are converted to shades of gray, 9 Adjust Dynamic Range thereby increasing the adjustable range of contrast. Optimizes image quality and allows user to reduce beam intensity. 2% increments 10 Power output between 0-100%. Values greater than 0.1 are displayed. Chapter 4 Functional Checks 4-15

[Page 100] 4-3-9 Color Flow Mode Checks 4-3-9-1 Preparations 1.) Connect one of the probes listed in 3-6-6 "Available Probes" on page 3-25, in Chapter 3 Installation to the System probe connector. 2.) Turn ON the scanner (if it isn’t turned on already). Primary Menu Secondary Menu CF Mode Gain Figure 4-11 Controls available in Color Flow Mode Figure 4-12 CFM Mode Screen Picture Example 4-16 Section 4-3 - General Procedure

[Page 101] 4-3-9-2 Color Flow Mode OP Panel Controls Table 4-7 Color Flow Mode OP Panel Controls Step Task Expected Result(s) comments 1 Press CFM-Mode key CFM Mode Starts Amplifies the overall strength of the echoes processed in the Color Flow window. Turn the 2 Adjust Gain Gain dial (CFM Mode key) to the left/right to increase/decrease Gain. Chapter 4 Functional Checks 4-17

[Page 102] 4-3-9-3 Color Flow Mode Softemenu Key Table 4-8 Color Flow Mode Softmenu Key Threshold assigns the gray scale level at 1 Threshold which color information stops. Controls the number of samples gathered for 2 Packet Size a single color flow vector. Allows a specific color map to be selected. 3 Select Color maps After a selection has been made, the color bar displays the resultant map. Enables the adjustment of the probe’s operating frequency. Press Frequency and 4 Adjust Frequency select desired value. The selected frequency is displayed in the status window. Averages color frames. Press Frame 5 Set Frame Average Average up/down to smooth temporal averaging. Views blood flow from a different perspective. 6 Color Invert Press Invert to reverse the color map. Trades frame rate for sensitivity and spatial For LOGIQ e, LOGIQ resolution. If the frame rate is too slow, e Vet and LOGIQ i Adjust LIne Density reduce the size of the region of interest, select a different line density setting, or reduce the packet size. Trades frame rate for sensitivity and spatial For Vivid e resolution. If the frame rate is too slow, Adjust Frame Rate reduce the size of the region of interest, select a different line density setting, or reduce the packet size. Adjust Spatial Filter to smooth out the color, 8 Activate Spatial Filter makes it look less pixely. Dynamic Range controls how echo intensities are converted to shades of gray, 9 Adjust Dynamic Range thereby increasing the adjustable range of contrast. Eliminates the motion artifacts. Press Ace to 10 Activate ACE activate. Slants the Color Flow region of interest or the 11 Adjust Angle Steer Doppler line to obtain a better Doppler angle. Adjusts the baseline to accommodate faster 12 Move Baseline or slower blood flows to eliminate aliasing. 4-18 Section 4-3 - General Procedure

[Page 103] Table 4-8 Color Flow Mode Softmenu Key Velocity scale determines pulse repetition frequency. If the sample volume gate range Change PRF exceeds single gate PRF capability, the For LOGIQ e, LOGIQ (Pulse Repetition Frequency) system automatically switches to high PRF e Vet and LOGIQ i mode. Multiple gates appear, and HPRF is indicated on the display. Velocity scale determines pulse repetition frequency. If the sample volume gate range Change scale exceeds single gate PRF capability, the For Vivid e system automatically switches to high PRF mode. Multiple gates appear, and HPRF is indicated on the display. 14 Transparency Map Allows to select specific transparency map Increases the number of transmit focal zones or moves the focal zone(s) so that you can tighten up the beam for a specific area. A 15 Focus Position graphic caret corresponding to the focal zone position(s) appears on the right edge of the image. Optimizes image quality and allows user to reduce beam intensity. 10% increments 16 Power output between 0-100%. Values greater than 0.1 are displayed. Wall Filter insulates the Doppler signal from For LOGIQ e, LOGIQ Wall Filter excessive noise caused from vessel e Vet and LOGIQ i 17 movement. Low Vel Reject insulates the Doppler signal Low Vel Reject from excessive noise caused from vessel For Vivid e movement. To enter PDI (Power Doppler Imaging) mode while not in CARD application. For CARD 18 Angio For Vivid e application, there’s no “Angio“ rotary on primary menu. Chapter 4 Functional Checks 4-19

[Page 104] 4-3-10 Doppler Mode Checks 4-3-10-1 Preparations 1.) Connect one of the probes listed in 3-6-6 "Available Probes" on page 3-25, in Chapter 3 Installation to the System probe connector. 2.) Turn ON the scanner (if it isn’t turned on already). Primary Menu Secondary Menu PW Mode Gain M/D Cursor B Pause Figure 4-13 Controls available in Doppler Mode Figure 4-14 Doppler Mode Screen Picture Example 4-20 Section 4-3 - General Procedure

[Page 105] 4-3-10-2 Doppler Mode OP Panel Controls Table 4-9 Doppler Mode OP Panel Controls 1 Press PW Mode key PW Mode Starts Amplifies the overall strength of the echoes processed in the Color Flow window. Turn the 2 Adjust Gain Gain dial (PW Mode key) to the left/right to increase/decrease Gain. Displays the M/D-Mode cursor on the B-Mode image. Press Cursor and Trackball to position 3 Display M/D-Mode Cursor sample volume graphic. Click SV gate to adjust sample volume gate size. Toggle between simultaneous and update presentation while viewing Spectral Doppler. 4 B-Pause Press B Pause to toggle between simultaneous and update. Chapter 4 Functional Checks 4-21

[Page 106] 4-3-10-3 Doppler Mode OP Panel Controls Table 4-10 Doppler Mode Touch Panel Controls Step Task Expected Result(s) comments Selects a level below which echoes will not be amplified (an echo must have a certain 1 Adjust Rejection minimum amplitude before it will be processed). Changes the speed at which timeline is 2 Adjust Sweep Speed swept. Press Sweep Speed up/down to increase/decrease the value. Displays only timeline screen. Press the Full 3 Activate Full Timeline Timescreen to activate. Display layout can be preset to have B-Mode For LOGIQ e, LOGIQ e Select Display Format and Time-motion side-by-side or over-under. Vet and LOGIQ i Display layout can be preset to have B-Mode Select Layout For Vivid e and Time-motion side-by-side or over-under. Enables the adjustment of the probe’s operating frequency. Press Frequency and 5 Adjust Frequency select desired value. The selected frequency is displayed in the status window. 6 Trace Direction Allows to select different trace direction. Vertically inverts the spectral trace without affecting the baseline position. Press invert to 7 Invert invert the spectral trace. The Plus and Minus signs on the velocity scale reverse when the spectrum is inverted. For LOGIQ e, LOGIQ e 8 Auto Calculation Enables or disables auto calculation. Vet and LOGIQ i Activates the window to modify the auto 9 Modify Calcs calculation items. 10 Trace Method Allows to select different trace method. Colorize the gray scale image to enhance the eyes’ discrimination capability. Press the 11 Activate Colorize Cololize, Trackball to cycle through available maps and press Set to select. Displays a map window adjacent to the image. Move the trackball to select the map. 12 Activate Gray Map The image reflects the map as scrolled through the selections. Press Set to select. Controls how echo intensities are converted 13 Dynamic Range to shades of gray. Click Dynamic Range to increase/decrease the value. Estimates the flow velocity in a direction at an angle to the Doppler vector by computing 14 Adjust Angle Correct the angle between the Doppler vector and the flow to be measured. Slant the Color Flow linear image left or right to get more information without moving 15 Adjust Angle Steer probes. Click Angle Steer to the left to slant the linear image. 4-22 Section 4-3 - General Procedure

[Page 107] Table 4-10 Doppler Mode Touch Panel Controls Step Task Expected Result(s) comments Adjusts the baseline to accommodate faster 16 Move Baseline or slower blood flows to eliminate aliasing. Velocity scale determines pulse repetition frequency. If the sample volume gate range Change PRF (Pulse Repetition exceeds single gate PRF capability, the For LOGIQ e, LOGIQ e Frequencies) - (Wall Filter) system automatically switches to high PRF Vet and LOGIQ i mode. Multiple gates appear, and HPRF is indicated on the display. Velocity scale determines pulse repetition frequency. If the sample volume gate range exceeds single gate PRF capability, the Change Scale - (Low Vel Reject) For Vivid e system automatically switches to high PRF mode. Multiple gates appear, and HPRF is indicated on the display. Adjusts the sensitivity to get more accurate 18 Trace Sensitivity envelope trace. 19 Time Resolution Adjusts the resolution in frequency domain. Optimizes the smoothness of the spectrum. 20 Spectral Average Different levels can be selected. Optimizes image quality and allows user to 21 Power output reduce beam intensity. 10% increments between 0-100%. 22 SV Length Sizes the sample volume gate. Wall Filter insulates the Doppler signal from For LOGIQ e, LOGIQ e Wall Filter excessive noise caused from vessel Vet and LOGIQ i movement. Wall Filter insulates the Doppler signal from Low Vel Reject excessive noise caused from vessel For Vivid e movement. Chapter 4 Functional Checks 4-23

[Page 108] 4-3-11 CWD Functional Check 4-3-11-1 Preparations 1.) Connect 3S-RS/6S-RS/6Tc-RS Probe to the system, see in Chapter 3 Installation. 2.) Turn ON the scanner (if it isn’t turned on already). 4-3-11-2 Activating CW Doppler To activate CW Doppler Mode: Ensure that the appropriate CW probe is connected. • For LOGIQ e, LOGIQ e Vet and LOGIQ i, press F6 on the keyboard to enter CW mode. F6 is the predefined function key for CW, which can be configured in Utility/Config -> Admin -> Function Key preset menu. • For Vivid e, press CW Key on the keyboard. The Doppler Spectrum appears, along with the CW Top/Sub Menu Menu. Figure 4-1. CWD Screen The following CW parameters are displayed: Frequency, Gain, Acoustic Output, Scale, Wall Filter and Dynamic Range. 4-3-11-3 Exiting CW Doppler To exit CW Doppler Mode, • For LOGIQ e, LOGIQ e Vet and LOGIQ i, press F6. • For Vivid e, press CW. 4-24 Section 4-3 - General Procedure

[Page 109] 4-3-12 Basic Measurements NOTE: The following instructions assume that you first scan the patient and then press Freeze . 4-3-12-1 Distance and Tissue Depth Measurements 1.) Press MEASURE once; an active caliper displays. 2.) To position the active caliper at the start point (distance) or the most anterior point (tissue depth), move the TRACKBALL . 3.) To fix the start point, press Set . The system fixes the first caliper and displays a second active caliper. 4.) To position the second active caliper at the end point (distance) or the most posterior point (tissue depth), move the TRACKBALL . 5.) To complete the measurement, press SET . The system displays the distance or tissue depth value in the measurement results window. 4-3-12-2 Circumference/Area (Ellipse) Measurement 1.) Press MEASURE once; an active caliper displays. 2.) To position the active caliper, move the TRACKBALL . 3.) To fix the start point, press SET . The system fixes the first caliper and displays a second active caliper. 4.) To position the second caliper, move the TRACKBALL . 5.) Adjust the ELLIPSE ; an ellipse with an initial circle shape appears. 6.) To position the ellipse and to size the measured axes (move the calipers), move the TRACKBALL . 7.) To increase the size, rotate the ELLIPSE button clockwise. To decrease the size, contrarotate the ELLIPSE button. 8.) To complete the measurement, press SET . The system displays the circumference and area in the measurement results window. 4-3-12-3 Worksheets Measurement/Calculation worksheets are available to display and edit measurements and calculations. There are generic worksheets as well as Application specific worksheets. The worksheets are selected from the Measurement Touch Panel. 4-3-13 Probe/Connectors Usage 4-3-13-1 Connecting a probe 1.) Place the probe's carrying case on a stable surface and open the case. 2.) Carefully remove the probe and unwrap the probe cable. 3.) DO NOT allow the probe head to hang free. Impact to the probe head could result in irreparable damage. 4.) Align the connector with the probe port and carefully push into place. 5.) Lock the probe latch upward. 6.) Carefully position the probe cord so it is free to move and is not resting on the floor. 4-3-13-2 Activating the probe The probe activates in the currently-selected operating mode. The probe's default settings for the mode and selected exam are used automatically. Chapter 4 Functional Checks 4-25

[Page 110] 4-3-13-3 Deactivating the probe 1.) Press the Freeze key. 2.) Gently wipe the excess gel from the face of the probe. (Refer to the Basic User Manual for complete probe cleaning instructions.) 3.) Carefully slide the probe around the right side of the keyboard, toward the probe holder. Ensure that the probe is placed gently in the probe holder. 4-3-13-4 Disconnecting the probe Probes can be disconnected at any time. However, the probe should not be selected as the active probe. 1.) Unlock the probe latch downward. 2.) Pull the probe and connector straight out of the probe port. 3.) Carefully slide the probe and connector away from the probe port and around the right side of the keyboard. 4.) Ensure the cable is free. 5.) Be sure that the probe head is clean before placing the probe in its storage box. WARNING WARNING Take the following precautions with the probe cables: Do not bend. If you have purchased the cart option, be sure to keep probe cables free from the wheels. WARNING WARNING Be careful not to trip on the probe cables if using the device without the optional cart. 4-3-14 Using Cine 4-3-14-1 Activating CINE Press Freeze , then roll the Trackball to activate CINE. To start CINE Loop playback, press Run/Stop. To stop CINE Loop playback. press Run/Stop. 4-3-14-2 Quickly Move to Start/End Frame Press First to move to the first CINE frame; press Last to move to the last CINE frame. 4-3-14-3 Start Frame/End Frame Press the Start Frame Two-Button Softkey to move to the beginning of the CINE Loop. Adjust the Start Frame up/down Two-Button Softkey upward to move forward through the CINE Loop. Adjust the Softkey downward to move backward through the CINE Loop. Press the End Frame Two-Button Softkey to move to the end of the CINE Loop. Adjust the End Frame up/down Two-Button Softkey upward to move forward through the CINE Loop. Adjust the Softkey downward to move backward through the CINE Loop. 4-3-14-4 Adjusting the CINE Loop Playback Speed Adjust the Loop Speed up/down Two-Button Softkey to increase/decrease the CINE Loop playback speed. 4-3-14-5 Moving through a CINE Loop Frame By Frame Adjust the Frame by Frame up/down Two-Button Softkey to move through CINE memory one frame at a time. 4-26 Section 4-3 - General Procedure

[Page 111] 4-3-15 Image Management (QG) For Image Management functionality refer to the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Quick Guide. It talks about several topics: • Clipboard • Printing Images • Browsing and Managing an Exam’s Stored Image • Connectivity, and Dataflow Concept and Creation • Starting an Exam • Configuring Connectivity • TCP/IP • Services (Destinations) • Buttons • Views • Verifying and Pinging a Device Chapter 4 Functional Checks 4-27

[Page 112] 4-3-16 Backup and Restore Database, Preset Configurations and Images 4-3-16-1 Formatting Media 1.) To format the backup media, DVD-RW, select the UTILITY/CONFIG button on the Keyboard. 2.) Select CONNECTIVITY , then REMOVABLE MEDIA . Properly label and Insert the backup media. 3.) Select the media type from the drop down menu. 4.) Enter the label for the media as shown in Figure 4-15. It is best to use all capital letters with no spaces or punctuation marks. Press Format . Figure 4-15 Format and Verify Media 5.) The Ultrasound system displays a pop-up menu, as shown in Figure 4-16. When the formatting has been completed, press OK to continue. 6.) If desired, verify that the format was successful by returning to Utility/Config->Connectivity- >Tools->Removable Media and selecting VERIFY as shown in Figure 4-15. Figure 4-16 Format Successful Pop-up Menu 4-28 Section 4-3 - General Procedure

[Page 113] 4-3-16-2 Backup System Presets and Configurations NOTE: Always backup any preset configurations before a software reload. This ensures that if the presets need to be reloaded, after the software update, they will be the same ones the customer was using prior to service. 1.) Insert a formatted DVD into the drive. 2.) On the Keyboard, press UTILITY/CONFIG . 3.) On the LCD display, press SYSTEM . 4.) On the LCD display, select BACKUP/RESTORE . NOTE: If you are not logged in as GE Service or with administrator privileges, the Operator Login window is displayed. Log on with administrator privileges. 5.) In the Backup list, select Patient Archive, Report Archive and User Defined Configuration. 6.) In the Media field, select DVD-RW (or USB memory device). 7.) Select BACKUP . The system performs the backup. As it proceeds, status information is displayed on the Backup/Restore screen. Check here to backup presets and configurations Figure 4-17 Backup/Restore Menu Chapter 4 Functional Checks 4-29

[Page 114] 4-3-16-3 Restore System Presets and Configurations The restore procedure overwrites the existing database on the local hard disk drive. Make sure to CAUTION insert the correct DVD (or USB memory device). 1.) Insert the Backup/Restore DVD (or USB memory device) into the drive. 2.) On the Keyboard, press UTILITY/CONFIG . 3.) On the LCD display, press SYSTEM . 4.) On the LCD display, select BACKUP/RESTORE . NOTE: If you are not logged in with administrator privileges, the Operator Login window is displayed. Log on with administrator privileges. 5.) In the Restore list, select Patient Archive, Report Archive and User Defined Configuration. 6.) In the Media field, select the Backup/Restore DVD-RW (or USB memory device). 7.) Select RESTORE . The system performs the restore. As it proceeds, status information is displayed on the Backup/Restore screen. After the Restore completes, the system will automatically reboot. Check here to restore presets and configurations. Figure 4-18 Backup/Restore Menu 4-30 Section 4-3 - General Procedure

[Page 115] 4-3-16-4 Archiving Images 1.) Insert the archive media. To format the archive media, DVD-RW, select the Utility/Config button on the Keyboard. NOTE: For LOGIQ e R5.x.x, LOGIQ e R6.x.x, LOGIQ e R7.x.x, LOGIQ e Vet, Vivid e R5.x.x, Vivid e R6.x.x and LOGIQ i R5.x.x, USB HDD also can be used as archive media. 2.) Select Connectivity, then Removable Media. 3.) Format the DVD-RW. Verify the format if desired. 4.) Images will be moved from the hard disk drive by date. Therefore, the best way is to label media by date. NOTE: Images will be moved from the hard disk drive by date. Therefore, the best way to label media is by date. When images are moved to the archive media, they will be deleted from the system hard disk drive. However, the patient database (backed up earlier) maintains pointers to the location of the images on the archive media. Figure 4-19 Format DVD-RW Screen 5.) Select Backup/Restore, then EZBackup/Move. NOTE: For LOGIQ e R4.x.x, LOGIQ i R4.x.x and Vivid e R4.x.x, there is one buttons for EZBackup/ Move, while for LOGIQ e R5.x.x, LOGIQ e R6.x.x, LOGIQ e R7.x.x, LOGIQ e Vet, LOGIQ i R5.x.x, Vivid e R5.x.x, and Vivid e R6.x.x, there are two buttons for EZBackup and EZMove. 6.) Select “Backup File Older Than in Days”. Choose the days which want to older than current exam date. Figure 4-20 EZBackup/Move Chapter 4 Functional Checks 4-31

[Page 116] 4-3-16-4 Archiving Images (cont’d) 7.) Press PATIENT and set the Dataflow to store images directly to DVD-ROM. 8.) From the image screen, press EZBACKUP/MOVE . The Move Images pop-up appears. Figure 4-21 Image Archive Move Pop-up Menu 9.) Press Next on pop-up message. 10.)A media check message appears. Press OK to continue. Figure 4-22 Media check message 4-32 Section 4-3 - General Procedure

[Page 117] 4-3-16-4 Archiving Images (cont’d) 11.)Press Finish after Backup/Move complete. Figure 4-23 EZBackup/Move complete All databases, presets and images should now be saved to removable media. 4-3-16-5 Emergency Repair Disk 1.) Connect the USB HDD to system. 2.) Select Backup/Restore, then Emergency Repair Disk. 3.) Select “Reminder Dialog Interval Days”. Reminder Dialog Interval Days Figure 4-24 Emergency Repair Disk Chapter 4 Functional Checks 4-33

[Page 118] 4.) Return to scan mode. Press Ctrl + B, the Emergency Disk Making window pop-up appears. Figure 4-25 Emergency Disk Making Pop-up Menu 5.) Press Next on pop-up message. 6.) A storage information message appears. Press Next to continue. Figure 4-26 Storage Information message 4-34 Section 4-3 - General Procedure

[Page 119] 7.) Press Finish after Emergency Disk Making complete. Figure 4-27 Emergency Disk Making Complete All databases, presets and images should now be saved to Emergency Disk. 8.) Press Ctrl + R, Emergency Disk Recovery will pop-up. Figure 4-28 Emergency Disk Recovery 9.) Press Next on pop-up message. Chapter 4 Functional Checks 4-35

[Page 120] 10.)A recovery information message appears. Press Next to continue. Figure 4-29 Recovery Information message 11.)Press Finish after Emergency Disk Recovery complete. Figure 4-30 Emergency Disk Recovery Complete 4-36 Section 4-3 - General Procedure

[Page 121] Section 4-4 Software Configuration Checks Table 4-11 Software Configuration Checks Step Task to do Expected Result(s) 1. Check Date and Time setting Date and Time are correct 2. Check that Location (Hospital Name) is correct Location Name is correct 3. Check Language settings Desired Language is displayed 4. For LOGIQ e, LOGIQ e Vet, LOGIQ i, the default function for Print1-3 Keys is P1 (store image); P2 (print); P3 (USB Quick Save). Print1-3 Keys can also be assigned as desired by the customer Check assignment of Printer Keys For Vivid e, the default function for Store Key and Print1- 2 Keys is Store (store image); P1 (print); P2 (USB Quick Save). Store Key and Print1-2 Keys can also be assigned as desired by the customer 5. Check that all of the customer’s options are set up correct All authorized functions are enabled Section 4-5 Peripheral Checks NOTE: Please refer to Peripherals Manual for detail procedures of each peripheral check. Check that peripherals work as described below: Table 4-12 Peripheral Checks Step Task to do Expected Result(s) 1. Press ( FREEZE ) Stop image acquisition. Press the default print key on the Control 2. The image displayed on the screen is printed on printer. Panel Connect with Foot witch on USB port and 3. To start image acquisition (the same function as ( FREEZE ) key). press once. Chapter 4 Functional Checks 4-37

[Page 122] This page was intentionally left blank. 4-38 Section 4-5 - Peripheral Checks

[Page 123] Chapter 5 Components and Functions (Theory) Section 5-1 Overview This chapter explains LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e ’s system concepts, component arrangement, and subsystem function. It also describes the Power Distribution System (PDS) and probes. Table 5-1 Contents in Chapter 5 Section Description Page Number 5-1 Overview 5-1 5-2 Block Diagrams and Theory 5-2 5-3 Power Diagrams 5-6 5-3 Power Diagrams 5-6 5-4 Common Service Platform 5-10 Chapter 5 Components and Functions (Theory) 5-1

[Page 124] Section 5-2 Block Diagrams and Theory 5-2-1 Block Diagram USC Probe Connector LCD TX64 15” XGA TMST(RFI/Carrier) Speaker RX64 On board LV unit Distributed CWD Peripherals HV unit (option) Power PS2 USB DVD-RW Keyboard I/O USB-Wireless A/N key USB2.0 LAN Audio Trackball Printer Battery Charger Ethernet and MUX SMBus U/S key Foot SW VGA Soft menu key Docking ECG AC Li-Ion Adapter Battery TGC VCR Limited backlit Cart Figure 5-1 LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e System Block Diagram • Pre Amp: Preamplifier • OQX2: Beamforming ASIC • CHACOM: B/M/CFM/DOP mode signal processor ASIC • DSP: Digital Signal Processor with PCI interface between CPU and TMST • HV unit: High voltage unit • LV unit: Low voltage unit • DC/DC & HV Ctrl, SMBUS I/F: DC/DC high voltage control smart bus interface • TUSC FPGA: LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Ultrasound controlling and Image data transfer FPGA 5-2 Section 5-2 - Block Diagrams and Theory

[Page 125] 5-2-2 General Information • LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e is an ultrasound imaging scanner. • The system can be used for: - 2D Black and White imaging - 2D Color Flow - M-Mode Black and White imaging - Doppler - A number of combinations of the above • LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e is a digital beam forming system that can handle up to 128 elements linear probes. • Signal flow from the Probe Connector Panel to the Front End, to the Mid Processors and Back End Processor and finally to the LCD and peripherals. • System configuration is stored on a hard disk drive and all necessary software is loaded from the hard disk drive on power up. Chapter 5 Components and Functions (Theory) 5-3

[Page 126] 5-2-3 External I/O Figure 5-2 External I/O module overview External I/O: The external I/O is the interface between the scanner and all external items. Examples: wireless network, USB interface medical grade printer and external medical grade SVGA displayer. 5-2-4 Peripherals DVD-RW, and a Black & White Video Printer can be connected to the external I/O. 5-4 Section 5-2 - Block Diagrams and Theory

[Page 127] 5-2-5 Wiring Figure 5-3 Wiring Diagram • TX64: Transmit board • RX64: Front end processing board • TMST: Master board • PWR SW: Power Switch • FPC: Flexible Print Circuit board Chapter 5 Components and Functions (Theory) 5-5

[Page 128] Section 5-3 Power Diagrams 5-3-1 Overview The AC Power assy’s main tasks are to isolate and output to the DC/DC unit which is inside the system console. The input of AC power pack will be the AC outlet and it’s universal, the range is AC 90V-264V, 47-63Hz. And no main power switch located on this power pack. 5-3-2 AC Power TMST & TX64 Figure 5-4 AC Power Distribution Block Diagram The mains cord has plugs in one side end. A male plug connects to the mains outlet on site. The mains voltage is routed to the AC power pack through a Circuit Breaker located on the site. The Circuit Breaker is of the auto fuse type, if for some reason the current grows to high, the switch will automatically break the power. From the Main Circuit Breaker, the AC power is routed via an Inrush Current Limiter to a internal outlet connector for the Mains Transformer. 5-6 Section 5-3 - Power Diagrams

[Page 129] 5-3-3 Battery charging The charging circuit is lithium-Ion battery charge and discharge controller. This block can switch the power between the battery and the output of AC Pack. If the output of AC Pack is available, the power input of Charge Board Unit should be from the AC Pack and the battery will be charged if it’s not full. This block will be also in charge of the battery charging monitor to avoid the battery over heat and over charging, charging will be shut off automatically if battery is charged fully. The battery will discharge to provide the power to the system when out of AC power pack output or AC line. Chapter 5 Components and Functions (Theory) 5-7

[Page 130] 5-3-4 Air Flow Distribution Figure 5-5 Air Flow Inside the Scanner The two air flow passes allow the scanner to be cooled down as shown in the figure above. • Path A (Bottom front > CPU Assy > Bottom left) for TMST & CPU Assy cooling. • Path B (Bottom front > TX64/RX64 > Bottom right) for TX64/RX64 cooling. 5-8 Section 5-3 - Power Diagrams

[Page 131] 5-3-5 Fans Figure 5-6 Left & Right Fans The scanner contains the four fans at the following positions for producing an air flow. - One fan assy: On the Left side for air flow path A. - One fan assy: On the Right side for air flow path B. Chapter 5 Components and Functions (Theory) 5-9

[Page 132] Section 5-4 Common Service Platform 5-4-1 Introduction The Service Platform contains a set of software modules that are common to all PC backend ultrasound and cardiology systems. The Common Service Platform will increase service productivity and reduce training and service costs. 5-4-2 Global Service User Interface (GSUI) 5-4-2-1 Internationalization The user interface provided by the service platform is designed for GE personnel and as such is in English only. There is no multi-lingual capability built into the Service Interface. 5-4-2-2 Service Login Select Utility/Config->Service. This button links the user to the service login screen. Figure 5-7 Service Login Screen 5-4-2-3 Access / Security The service interface has different access and security user levels. Each user is only granted access to the tools that are authorized for their use. 5-10 Section 5-4 - Common Service Platform

[Page 133] 5-4-2-3 Access / Security (cont’d) Table 5-2 Service Login User Levels User Level Access Authorization Password Operator uls Authorized access to specified diagnostics, error logs and utilities. Same Administrator uls acquisition diagnostic tests as GE Service. External Service gogems Every access request, whether successful or not, will be logged into a service access log that is viewable to authorized users. 5-4-2-4 The usage for security cable The ultrasound system equipped with Kensington security slot which is compatible with a Kensington security cable, refer toFigure 5-8 on page 5-11 . Figure 5-8 Kensington security slot How to prevent unauthorized removal of the ultrasound system? 1.) Wrap the cable around the immovable object, refer to Figure 5-9 on page 5-11 ; 2.) Make sure and rotate the key to the right (unlocked position); 3.) Insert the lock into the Kensington security slot in the system side cover, refer to Figure 5-9 on page 5-11 ; 4.) Rotate the key to the left (locked position). 5.) For more information, visit www.kensington.com. Figure 5-9 Kensington security slot and system NOTE: Full maintenance reboot should be selected after the service dongle is used on the system. Chapter 5 Components and Functions (Theory) 5-11

[Page 134] 5-4-3 Service Home Page The navigation bar at the top of the screen allows the user to select from several tools and utilities. Figure 5-10 Customer Service Home Page 5-12 Section 5-4 - Common Service Platform

[Page 135] 5-4-4 Error Logs Tab From the Error Logs Tab the Log Viewer displays four categories with pull-down sub-menus and an Exit selection. The Service Interface allows scanner logs to be viewed by all service users. The log entries are color-coded to identify the error level severity at a glance. Table 5-3 Log Entry Key Severity Error Level Color Code 1 Information Green 2 Warning Blue 3 Error Red The Service Interface supports the transfer of these logs to local destinations such as the CD-ROM drive. Figure 5-11 Log Viewer / Logs / Log Entries Chapter 5 Components and Functions (Theory) 5-13

[Page 136] 5-4-4-1 Logs The seven sub-menus of the Logs category are System, Power, Infomatics, Temperature, Probe, Board, and DICOM. NOTE: Figure 5-11 provides a graphical example of the log entries for the System Logs . Log table headings for the different logs are as follows: • System Log entry headings include Time Stamp; Error Level; Package; and Error Message. • Power Log entry headings include Time Stamp; Error Level; Package; and Error Message. • Infomatics Log entry headings include TimeStamp, Revision, PtID, PtDOB, PtSex, PtWeight, PtHeight, ExamID, Exam Category, ExamCurDate, ExamStartTime, ExamEndTime, FreezeTime, TimeOfImageArchived, AccessionNumber, RefPhyName, ReadingPhyName, Operator, RoomNo, BodyPatternSelected, InstitutionName, ActiveModeTime, CalculationMade, CalculationTime, HelpUsage, ProductName, SystemSWRev, NoOfSWModules, SystemPowerOnTime, SystemIdleTime, NoOfBoards, ProbeChangedDate, ProbeChangedTime, ProbeChangedStatus, NoOfProbeSlots, NoOfProbes, ProbeID, ProbeSerialNumber, and ActiveExamProbes. • Temperature Log entry headings include Time Stamp; Error Level; Package; CPU Internal Temp, TMST Process Temp, TMST Internal Temp, TMST Remote Temp, TX64 Process Temp, TX64 Internal Temp, TX64 Remote Temp, TMST 3.3V, TMST 5V, TMST 12V, TMST 1.2V, TMST 1.5V, TMST 1.8V, TX64 1.5V, TX64 1.8V, TX64 3.3V, TX 64 5V, TX649V, TX64 12V, TX 64 +THV, TX64-THV, TX64+SHV, and TX64-SHV. • Probe Log entry headings include Time Stamp; Error Level; Package; Error Message; Severity; Revision; and three new labels that have not yet been named. • Board Log entry headings include Time Stamp; Error Level; Package; Board; Severity; Revision and two new labels that have yet been named. • DICOM Log entry headings include Time Stamp; Error Level; Package; and Error Message. • Touch Screen (only for LOGIQ e R5.2.x) Log entry headings include Touch Screen operation events. 5-14 Section 5-4 - Common Service Platform

[Page 137] 5-4-4-2 Utilities The two sub-menus of the Utilities category are Plot Log, and Plot Page. Plot Log Plot Page Figure 5-12 Utilities Sub-Menus • Plot Log Allows for the color coded plot of all Log contents with the package on the ‘x’ axis and incident count on the ‘y’ axis. • Plot Page Allows for the color coded plot of all Page contents with the package on the ‘x’ axis and incident count on the ‘y’ axis. 5-4-4-3 Search On the Text Search sub-menu of the Search category, users enter case-sensitive text they wish to find. This filter field works well for filtering the Sys log file for the word “fail”. Figure 5-13 Search Sub-Menu Chapter 5 Components and Functions (Theory) 5-15

[Page 138] 5-4-4-4 Exit The sub-menu, Exit Log Viewer , returns the user to the Service Desktop home page. Figure 5-14 Exit Log Sub-Menu 5-16 Section 5-4 - Common Service Platform

[Page 139] 5-4-5 Diagnostics Detailed Diagnostic information is found in Chapter 7. Figure 5-15 User Diagnostic Page 5-4-5-1 Diagnostics Execution Diagnostic tests are executable by both local and remote users. The Service Platform provides top-level diagnostic selection based on the user’s level and login access permissions. Remote access will require disruptive diagnostic permissions to run Acquisition diagnostics. 5-4-5-2 Diagnostic Reports Diagnostic tests return a report to the Service Platform. The platform retains the report and allows for future viewing of the diagnostic logs. Chapter 5 Components and Functions (Theory) 5-17

[Page 140] 5-4-6 Image Quality The Image Quality page is intended to contain tools for troubleshooting image quality issues. FIELD IS NOT YET POPULATED Figure 5-16 Image Quality Page 5-4-7 Calibration The Calibration page is intended to contain the tools used to calibrate the system. FIELD IS NOT YET POPULATED Figure 5-17 Calibration Page 5-18 Section 5-4 - Common Service Platform

[Page 141] 5-4-8 Configuration The Configuration page is intended to be used to setup various configuration files on the system. The Service Platform is the access and authorization control for remote access to the configuration subsystem. The enable/disable of software options can be done from this Configuration page. Figure 5-18 Configuration Page 5-4-9 Utilities The Utilities page contains several miscellaneous tools. Chapter 5 Components and Functions (Theory) 5-19

[Page 142] 5-4-10 Replacement The Replacement page is intended to contain the tools used to track replacement parts used in the system. FIELD IS NOT YET POPULATED Figure 5-19 Part Replacement Page 5-4-11 PM The PM page is intended to contain the tools used in periodic maintenance of the system. FIELD IS NOT YET POPULATED Figure 5-20 Planned Maintenance Page 5-20 Section 5-4 - Common Service Platform

[Page 143] Chapter 6 Service Adjustments Section 6-1 Overview 6-1-1 Purpose of this chapter 6 This section describes how to test and adjust the scanner. These tests are optional. You may use them to check the system for errors. Table 6-1 Contents in chapter Section Description Page Number 6-1 Overview 6-1 6-2 Monitor Adjustments 6-2 Chapter 6 Service Adjustments 6-1

[Page 144] Section 6-2 Monitor Adjustments 6-2-1 Adjustments Procedures To adjust the brightness and volume: 1.) Press Ctrl + brightness key together (up/down), located on the keyboard. 1.) Press Ctrl + volume key together (left/right), located on the keyboard. Figure 6-1 LCD Monitor 6-2 Section 6-2 - Monitor Adjustments

[Page 145] Chapter 7 Diagnostics/Troubleshooting Section 7-1 Overview 7-1-1 Purpose of Chapter 7 This section describes how to setup and run the tools and software that help maintain image quality and system operation. Very basic host, system and board level diagnostics are run whenever power is applied. Some Service Tools may be run at the application level. However most software tests are required. Table 7-1 Contents in Chapter 7 Section Description Page Number 7-1 Overview 7-1 7-2 Gathering Trouble Data 7-2 7-3 USB Quick Save 7-4 7-4 Screen Captures 7-6 7-5 Global Service User Interface (GSUI) 7-9 7-6 Common Diagnostics 7-12 7-7 Network and Insite II Configuration 7-15 Chapter 7 Diagnostics/Troubleshooting 7-1

[Page 146] Section 7-2 Gathering Trouble Data 7-2-1 Overview There may be a time when it would be advantageous to capture trouble images and system data (logs) for acquisition to be sent back to the manufacturer for analysis. There are different options to acquire this data that would give different results. 7-2-2 Collect Vital System Information The following information is necessary in order to properly analyze data or images being reported as a malfunction or being returned to the manufacturer: - Product Name = LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e From the Utility>System>About screen: Applications Software - Software Version - Software Part Number System Image Software - Image Revision - Image Part Number 7-2 Section 7-2 - Gathering Trouble Data

[Page 147] 7-2-3 Collect a Trouble Image with Logs If the system should malfunction, press the Alt-D keys simultaneously. This will collect a screen capture of the image monitor, system presets and the following logs: - Keyboard Shadow Log - Error Logs - Crash Log - Power Supply - Temperature NOTE: Power Supply and Temperature logs are not currently being updated by the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . This Alt-D function is available at all times. Figure 7-1 ALT-D Dialog Box When Alt-D is pressed, a menu box appears that allows for: - A place to enter a description of the problem - A choice to store to a pre-formatted DVD-R, RD (Removable Disk) or to the Export directory D: export. The subsequent file is compressed and time stamped. The screen capture is a bitmap which eliminates the possibility of artifacts from compression. Chapter 7 Diagnostics/Troubleshooting 7-3

[Page 148] Section 7-3 USB Quick Save 7-3-1 Overview There may be times when the customer or field engineer will want to directly save images into USB memory. This is accomplished by saving individual Cine clips (moving images- avi format) or still images (jpg format) directly to a USB memory disk by pressing a Print Key. For LOGIQ e, LOGIQ e Vet and LOGIQ i, the P3 key is the factory default print key to accomplish the USB Quick Save; for Vivid e, the P2 key is the factory default print key to accomplish the USB Quick Save. However, the default is for the Image Area only or the customer may have customized the default Key function. Here, take LOGIQ e for example and the P3 key is the factory default print key to accomplish the USB Quick Save. 7-3-2 Check and Record the P3 Key Function Check the function of the default Key in the event that the customer may have made some customized settings. 4.) In the Physical Print Buttons field, select Print3 key. The Connectivity/Buttons Screen will be displayed like the one shown in Figure 7-2 on page 7-4 . Figure 7-2 Buttons Set Up Screen P3 is the factory default USB Quick Save key. If it is not set to Image Area, proceed to step 5 to record the customer’s customized settings. 7-4 Section 7-3 - USB Quick Save

[Page 149] 7-3-2 Check and Record the P3 Key Function (cont’d) 5.) In the Destinations section, record the service that is displayed. 6.) In the Physical Print Buttons section, record the parameters related to the service. 7-3-3 Setting the P3 Key to USB Quick Save If the P3 Key is not set to USB Quick Save: 1.) While on the Connectivity screen, with the Buttons tab displayed, go to the Destinations list. 2.) From the list select USB Quick Save . Press [>>] to add the selection to the Printflow View section. 3.) Ensure that the Physical Print Buttons section for capture Area is set to Image Area and No Image Compression. 4.) The P3 Key should now be set up for USB Quick Save, sending the images directly to the USB memory. Chapter 7 Diagnostics/Troubleshooting 7-5

[Page 150] Section 7-4 Screen Captures There may be times when the customer or field engineer will want to capture a presentation on the screen. This is accomplished by first saving the image(s) to the clipboard using a Print Key. There’s no factory default print key to accomplish a secondary screen capture. However, customer may have customize any of Print Key function. Here, take Print1 button for example, for LOGIQ e, LOGIQ e Vet, LOGIQ i, Print1, Print 2 and Print3 are the same, for Vivid e, Store, Print1 and Print2 are the same. Therefore, screen capture should involve the following steps: 1.) Check and record any custom settings for the Print1 button. 2.) Set the Print1 button to Whole Screen, Secondary Capture. 3.) Capture the required screens to the Hard Disk Drive or DVD-R. 4.) Restore the Print1 button to it’s original settings. 7-4-1 Check and Record the P1 Key Function Check the function of the Print1 Key in the event that the customer may have made some custom settings. 4.) In the Physical Print Buttons field, select Print1. The Connectivity/Buttons Screen will be displayed like the one shown in Figure 7-2 on page 7-4 . If P1 is not set to Whole Screen, as shown in Figure 7-2, proceed to step 5 to record the customer’s customized settings. 5.) In the Destinations section, record the service that is displayed. 6.) In the Physical Print Buttons section, record the parameters related to the service. 7-4-2 Setting the P1 Key to Screen Capture If the P1 Key is not set to screen capture: 1.) While on the Connectivity screen, with the Buttons tab displayed, go to the Destinations list. 2.) From the list select Copy To Dataflow . Press [>>] to add the selection to the Printflow View section. 3.) Ensure that the Physical Print Buttons section for capture Area is set to Whole Screen, secondary Capture and No Image Compression. 4.) The P1 Key should now be set up for whole screen capture, sending the screens to the image buffer (clipboard). 7-4-3 Capturing a Screen The following is a generic process to capture any screen from the scanner: 1.) Navigate to and display the image/screen to be captured. 2.) Press P1 . This will place a snapshot of the screen on the “clipboard” displayed at the bottom of the scan image display. 7-6 Section 7-4 - Screen Captures

[Page 151] 7-4-3 Capturing a Screen (cont’d) Clipboard Thumbnai ls Menu Figure 7-3 Select Image to Capture 3.) Click FREEZE to unfreeze the image to view the image screen and the snapshots displayed on the bottom. 4.) Highlight the snapshot to be stored. 5.) Select Menu on the right side of the image screen, then highlight and select SAVE AS. Save As Figure 7-4 Menu > Save As Chapter 7 Diagnostics/Troubleshooting 7-7

[Page 152] 7-4-3 Capturing a Screen (cont’d) For LOGIQ e R5.x.x, R6.x.x, R7.x.x, LOGIQ i R5.x.x, Vivid e R5.x.x, For LOGIQ e R4.x.x, LOGIQ i R4.x.x, Vivid e R4.x.x Figure 7-5 Save Dialog Box 6.) A Save dialog box will be opened. • For LOGIQ e R4.x.x, LOGIQ i R4.x.x, Vivid e R4.x.x, choose d:\export folder as the archive location to save the image on the DVD-R. • For LOGIQ e R5.x.x, LOGIQ e R6.x.x, LOGIQ e R7.x.x, LOGIQ i R5.x.x, Vivid e R5.x.x, Vivid e R6.x.x, select Save first, and Select Transfer to CD/DVD to save the image on the CD/DVD. 7-4-4 Reset the P1 Key to Customer’s Functionality If the customer had programmed the P3 Key to a function other than screen capture, restore that functionality recorded in section 7-4-1 on page 6. Refer to Figure 7-2. 4.) In the Physical Print Button field, select Print1. 5.) In the Destinations list, select the service(s) recorded in step 5, Section 7-4-1. 6.) In the Physical Print Buttons section, select the parameters related to the service recorded in step 6, Section 7-4-1. 7-8 Section 7-4 - Screen Captures

[Page 153] Section 7-5 Global Service User Interface (GSUI) 7-5-1 Enter global service user interface 1.) Press Utility/Config - Service, see Figure 7-6 on page 7-9 . Figure 7-6 system Service button 1.) Select GE Service in option of User Level of GEMS Service Home page and input correct password, press OK button. See Figure 7-7 on page 7-9 . Figure 7-7 Service Login Page Chapter 7 Diagnostics/Troubleshooting 7-9

[Page 154] 7-5-2 Active Diagnostic Function 2.) Choose Diagnostic in Global Service Interface to active diagnostic functions, choose options to activate various functions correspondingly. Figure 7-8 Active Diagnostic Function 7-5-3 Control Frame Contains the user interface elements used for: • Diagnostic control, and • Operator feedback 7-5-3-1 Button This button has two modes each with appropriate text: • Execute - to start the diagnostic, and • Abort - to stop a diagnostic The button can also be disabled. 7-5-3-2 Loop Count This is an editable text field that will only accept numeric values with 4 digits or less. When the button is configured as an “execute” button and pressed, the loop count field will be queried to determine the number of times to execute the diagnostic. 7-5-3-3 Progress Indicator Displays a graphical progress indication to the user. 7-10 Section 7-5 - Global Service User Interface (GSUI)

[Page 155] 7-5-3-4 Short Text Message Displays either a starting message or aborting message, as well as the diagnostic completion status. 7-5-3-5 Background Color Initially gray, the Control Frame background color changes upon completion of a diagnostic to indicate completion status. • Fail = Red • Pass = Green • Neither pass nor fail = Set back to Gray (for example, final code status is Aborted). Chapter 7 Diagnostics/Troubleshooting 7-11

[Page 156] Section 7-6 Common Diagnostics 7-6-1 Utilities Provides two selections: 7-6-1-1 Disruptive Mode Allows you to enable or disable disruptive mode troubleshooting. 7-6-1-2 System Shutdown Allows for system shutdown from the diagnostic menu. Select to Restart System or Shutdown System. Also, select to retain Disruptive Mode or Not. After submitting to restart or shutdown a confirmation screen gives one last chance to confirm or cancel the request. 7-12 Section 7-6 - Common Diagnostics

[Page 157] 7-6-2 PC Diagnostics (Non-Interactive Tests) 7-6-2-1 Essential Tests 7-6-2-2 System Board 7-6-2-3 Hard Disk Drive Surface Scan 7-6-2-4 Hard Disk Drive Quick Test 7-6-2-5 PCIBus 7-6-2-6 Video Card 7-6-2-7 Network Interface 7-6-2-8 CMOS 7-6-2-9 DRAM Memory 7-6-2-10 Parallel Port Chapter 7 Diagnostics/Troubleshooting 7-13

[Page 158] 7-6-3 PC Diagnostics (Interactive Tests) 7-6-3-1 Keyboard Test 7-6-3-2 Mouse Test 7-6-3-3 Audio Card Test (only for LOGIQ e R5.2.x and R6.x.x) 7-6-4 Restart the system after diagnostics Always shutdown the system and reboot after a diagnostics session. 7-14 Section 7-6 - Common Diagnostics

[Page 159] Section 7-7 Network and Insite II Configuration 7-7-1 Network Configuration 7-7-1-1 Wire-LAN Network 1.) Connect system with network. 2.) Press Utility/Config -> Connectivity -> TCPIP, in IP Settings window check the Enable DHCP box. In Network Speed box, choose the proper speed available. Figure 7-9 Enable DHCP Chapter 7 Diagnostics/Troubleshooting 7-15

[Page 160] 7-7-1-1 Wire-LAN Network (cont’d) NOTE: If user want to setup static IP address, uncheck Enable DHCP option, input static address in IP-Address box, Subnet Mask and Default Gateway box. In Network Speed box, choose the proper speed available. Figure 7-10 Input static address 3.) Click Save, in popped-up dialog choose Ok. Figure 7-11 Save and reboot inquiry dialog 4.) After reboot, the network icon at the left bottom of screen turns green. Figure 7-12 Network icon 7-16 Section 7-7 - Network and Insite II Configuration

[Page 161] 7-7-1-2 Wireless LAN Network 1.) Connect wireless LAN card with system. 2.) Click Start at the left bottom of screen, and select “Network Connections. Figure 7-13 Start menu 3.) In the pop-up window choose Wireless Network Connection. Click it with cursor key, then select View Available Wireless Networks. For LOGIQ e R5.x.x/R6.x.x/R7.x.x, Vivid e R5.x.x/R6.x.x, For LOGIQ e R4.x.x, LOGIQ i R4.x.x, Vivid e R4.x.x LOGIQ i R5.x.x Figure 7-14 Wireless Network Connection configuration Chapter 7 Diagnostics/Troubleshooting 7-17

[Page 162] 7-7-1-2 Wireless LAN Network (cont’d) 4.) The Wireless Network Connection dialog box displays. Select the proper wireless network in Available wireless networks window, check the Allow me to connect... box, and click Connect. For LOGIQ e R5.x.x/R6.x.x/R7.x.x, Vivid e R5.x.x/R6.x.x For LOGIQ e R4.x.x, LOGIQ i R4.x.x, Vivid e R4.x.x LOGIQ i R5.x.x Figure 7-15 Wireless Network Connection dialog box NOTE: If an encrypted network has been selected, input Network key in Wireless Network Connection dialog box displayed, and click Connect. Type network key here. Figure 7-16 Network key input 5.) The network icon at the left bottom of screen turns green. Figure 7-17 Network icon NOTE: To manually configure a wireless network, the involvement of the IT department is mandatory. 7-18 Section 7-7 - Network and Insite II Configuration

[Page 163] 7-7-2 Insite II Configuration 6.) Enter global service user interface, and log in as GE Service. See section 7-5-1 on page 9. 7.) To use Pilot Server , on Configuration page, choose Questra Agent Configuration in left column. Select Advanced Configuration, then choose “Others” as server type, and manually input pilot address, and click SAVE. Figure 7-18 Advanced_Configuration page (out of GE network) NOTE: If system is within GE network, choose Development as server type, and do not need step 9.) enter Proxy Server address . Figure 7-19 Advanced_Configuration page (within GE network) Chapter 7 Diagnostics/Troubleshooting 7-19

[Page 164] 8.) Change to Device Information page, enter Device and Serial Number as the serial number of that system, then press Modify Device Configurations. Figure 7-20 Device_Information page NOTE: The Device name and Serial Number entered should be unique on server. It can be read from the rating plate label. Figure 7-21 Rating plate label 7-20 Section 7-7 - Network and Insite II Configuration

[Page 165] 9.) Change to Proxy_Configuration page, enter Proxy Server Address as 3.20.128.6 and Proxy Server Port as 88, then press SAVE. Figure 7-22 Proxy_Configuration page Chapter 7 Diagnostics/Troubleshooting 7-21

[Page 166] 10.)Change to Diagnostics page. Enable Disruptive Mode at Service side by pressing Yes. Figure 7-23 Enable Disruptive Mode 11.)Customer will receive a request of Service side, click Yes to accept. Figure 7-24 Accept requirement of Service 7-22 Section 7-7 - Network and Insite II Configuration

[Page 167] 12.)Service can do Remote Diagnostics successfully. Figure 7-25 Remote Diagnostic successful 13.)Press power switch, and choose Full Maintenance Reboot to reboot system. Figure 7-26 Full Maintenance Reboot window Chapter 7 Diagnostics/Troubleshooting 7-23

[Page 168] 7-7-3 Insite II Configuration (For LOGIQ e R6.x.x and LOGIQ e R7.x.x) 1.) Enter global service user interface, and log in as GE Service. See section 7-5-1 on page 9. 2.) On Configuration page, select Insite ExC Agent Configuration in the left column, fill in the information in Agent Configuration, choose “PPODUCT” as Enterprise server in Advanced Configuration, please keep the default settings for other items, then click Submit Changes. Figure 7-27 Choose Enterprise server NOTE: The BOLD items can not be left blank. 7-24 Section 7-7 - Network and Insite II Configuration

[Page 169] 3.) Set Disruptive Mode Status as Enabled . Change to Utilities page. select Disruptive Mode in the left column, Check whether the Disruptive Mode Status is Enabled , if not, click Yes to change the Disruptive Mode Status as Enabled . See Figure 7-28 on page 7-25 . Figure 7-28 Device_Information page There is another way to Set Disruptive Mode Status as Enabled . Click Insite Icon in system status bar, choose Connect clinical Lifeline , the Insite Icon will change to RED, do not need to change if the insite icon is already RED. See Figure 7-29 on page 7-25 . Figure 7-29 Set Disruptive Mode Status Chapter 7 Diagnostics/Troubleshooting 7-25

[Page 170] 4.) Customer will receive a request of Service side, click Yes to accept. See Figure 7-30 on page 7-26 Figure 7-30 Accept requirement of Service 5.) Service can do Remote Diagnostics successfully. See Figure 7-31 on page 7-26 Figure 7-31 Remote Diagnostic successful 7-26 Section 7-7 - Network and Insite II Configuration

[Page 171] 6.) Press power switch, select Full Maintenance Reboot to reboot system, see Figure 7-32 on page 7- 27 . Figure 7-32 Full Maintenance Reboot window 7.) In remote server side, select the device type in DEVICE TYPE. Figure 7-33 device type window Chapter 7 Diagnostics/Troubleshooting 7-27

[Page 172] 8.) Select Update Software in the category of SERVICE. Figure 7-34 Update software 9.) The page of software package shows up, select the correct software package in the list. Then select SCHEDULE to set a proper time to upgrade the software. Figure 7-35 software package 7-28 Section 7-7 - Network and Insite II Configuration

[Page 173] 10.)Click “+” icon on the schedule page to set up a schedule. Fill in the name and time, then click Add. Figure 7-36 New schedule page 11.)Then the active schedule is shown on the SCHEDULE page. Figure 7-37 Active Schedule Chapter 7 Diagnostics/Troubleshooting 7-29

[Page 174] 12.)In device side, if the device is connected to network, a mail icon will show in the status bar. Figure 7-38 Status bar 13.)Press Power buuton. The SYSTEM-EXIT window shows up. Click Decline, the system will not download the software, and the Insite icon in the status bar will not shown. Click Download, the system will begin to download the software. Figure 7-39 System-Exit window NOTE: If the administrator is in remote side, press Alt+F1 to display the frontpanel simulator. Select the On/Off button, and the system-exit window shows up. Figure 7-40 Frontpanel Simulator window 7-30 Section 7-7 - Network and Insite II Configuration

[Page 175] NOTE: Make sure the system administrator is logged on as ADM, or the system will indicate such message. Figure 7-41 System-exit error 14.)The system begins to download the software, and wait until the process complete. If you click Pause, the download process will be paused. Click Download to re-start the process. If you click Cancel, the download process will stop. Figure 7-42 Software download process Chapter 7 Diagnostics/Troubleshooting 7-31

[Page 176] 15.)When the download is complete, it will show the window below. Figure 7-43 Download Complete window 16.)Restart the system, and the system CD will be loaded as shown in Figure 7-44 on page 7-32 . Figure 7-44 System CD loading 7-32 Section 7-7 - Network and Insite II Configuration

[Page 177] 17.)After the system is on, login as ADM. Press Power button, and the system-exit window displays. Select Verify. Figure 7-45 System-exit verify window 18.)It will show the verify items. Select Passed, and sign the signature, the upgrade completes. If any of the 10 items fails, the system will remind the user to restart the system to rollback to the previous version. Figure 7-46 Verify item Chapter 7 Diagnostics/Troubleshooting 7-33

[Page 178] 7-34 Section 7-7 - Network and Insite II Configuration

[Page 179] Chapter 8 Replacement Procedures Section 8-1 Overview 8-1-1 Purpose of Chapter 8 This chapter describes replacement procedures for the following modules and subsystems. Table 8-1 Contents in Chapter 8 Section Description Page Number 8-1 Overview 8-1 Disassembly/Re-assembly of LOGIQ e/LOGIQ e Vet/LOGIQ 8-2 8-1 i/Vivid e 8-2-1 Warning and Caution 8-1 8-2-2 Handle Assy (FRU No. 313) 8-2 8-3 Loading Base Image Software 8-4 8-4 Checks after FRU replacement (Debrief Guidelines) 8-9 Section 8-2 Disassembly/Re-assembly of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e 8-2-1 Warning and Caution WARNING WARNING ONLY QUALIFIED SERVICE PERSONNEL SHOULD REMOVE ANY COVERS OR PANELS. ELECTRICAL HAZARDS EXISTS AT SEVERAL POINTS INSIDE. BECOME THOROUGHLY FAMILIAR WITH ALL HAZARDOUS VOLTAGES AND HIGH CURRENT LEVELS TO AVOID ACCIDENTAL CONTACT CAUTION Do not wear the ESD wrist strap when you work on live circuits and more than 30V peak is present. Chapter 8 Replacement Procedures 8-1

[Page 180] 8-2-2 Handle Assy (FRU No. 313) Purpose: This is a description on how to remove and replace the Handle Assy (FRU No.313). 8-2-2-1 Tools • Plier 8-2-2-2 Needed Manpower • 1 person, 2 minutes + travel 8-2-2-3 Preparations • Shut Down the System. 8-2-2-4 Removal Procedure Refer to Figure 8-1 on page 8-3 . 1.) Unscrew the two handle caps on both sides of the system, the rotation direction is counterclockwise. 2.) Pull out the Handle. 8-2-2-5 Mounting procedure 1.) Install the new parts in the reverse order of removal. 8-2 Section 8-2 - Disassembly/Re-assembly of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e

[Page 181] 8-2-2 Handle Assy (FRU No. 313) (cont’d) 1) 2) Figure 8-1 Handle Assy Disassembly Chapter 8 Replacement Procedures 8-3

[Page 182] Section 8-3 Loading Base Image Software NOTE: While it is believed to be unnecessary, It would not hurt to disconnect the system from the network and remove all transducers. NOTE: Please ensure AC adapter is connected during system upgrade! 1.) Insert the disk labeled “System & Application Software” into the DVD ROM drive. 2.) Properly turn off the scanner by momentarily pressing the Power On/Off Switch. Select “Full Maintenance Reboot” from the System Exit menu. 3.) If the system will not shutdown normally, hold down the Power On/Off Switch until the light turns from green to amber. Figure 8-2 Shutdown Dialog Box 4.) Turn on the scanner. System will detect the DVD-RW automatically. 5.) Press any key to continue when below message display as shown in Figure 8-3 on page 8-4 . Figure 8-3 Update message 8-4 Section 8-3 - Loading Base Image Software

[Page 183] 6.) Select one of the options for loading the system. Select choice [a] to load the complete disk. Refer to Figure 8-4 on page 8-5 . Figure 8-4 Selection for loading the system WARNING WARNING While the software install procedure is designed to preserve data, you should select choice [b] to format disk C only. 7.) Press “Yes” or “No” to continue. Figure 8-5 Confirmation on loading the system Chapter 8 Replacement Procedures 8-5

[Page 184] 8.) System CD will be loaded as shown in Figure 8-6 on page 8-6 . Figure 8-6 System CD loading If the screen displays as show in Figure 8-7 on page 8-6 after input “Yes”, wait about 1 minute until Figure 8-6 on page 8-6 displays. Figure 8-7 System CD loading blank message NOTE: System CD will be loaded twice, and it will need about 20 minutes. 8-6 Section 8-3 - Loading Base Image Software

[Page 185] 9.) After finish updating system, refer to Figure 8-8 on page 8-7 . Figure 8-8 System upgrade complete 10.)Press any key to reboot system. When system first time boot up after upgrading complete, you will see the following message. Figure 8-9 Windows start 11.)Make a region selection when below message display as show in Figure 8-10 on page 8-7 . Figure 8-10 Region selection message NOTE: Step 11.) is only for LOGIQ e R4.x.x, LOGIQ i R4.x.x and Vivid e R4.x.x. Chapter 8 Replacement Procedures 8-7

[Page 186] NOTE: For LOGIQ e R5.x.x, R6.x.x, please select a package to run the application. For Emergency&Critical For Nerve&Needle For General Imaging Figure 8-11 Package selection message NOTE: For LOGIQ e R5.x.x, you need to select a package to run the application. 8-8 Section 8-3 - Loading Base Image Software

[Page 187] Section 8-4Checks after FRU replacement (Debrief Guidelines) Perform required Functional tests based upon the FRU being replaced. Table 8-2 Functional Tests Matrix of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Section No. Description Functional Tests Basic Functional 4-3-1, 4-3-2, 4-3-7, 4-3-8, 4-3-9, 4-3-10 Checks Handle function check: 8-2-2 313 Handle Assy 1. The system can be carried with the handle; 2. The handle can rotate from +90 to -110 degree Section Loading Base Image 4-3-1, 4-3-2, 4-3-7, 4-3-8, 4-3-9, 4-3-10, Section 4-4 8-3 Software Table 8-3 Functional Test key of LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e Key Functional Test/Diagnostics/Leakage Current 4-3-1 Power On/Boot Up 4-3-2 Power Off/ Shutdown 4-3-7 B Mode Checks 4-3-8 M Mode Controls 4-3-9 Color Flow Mode Checks 4-3-10 Doppler Mode Checks Section 4-4 Software Configuration Checks Chapter 8 Replacement Procedures 8-9

[Page 188] This page was intentionally left blank. 8-10 Section 8-4 - Checks after FRU replacement (Debrief Guidelines)

[Page 189] Chapter 9 Renewal Parts Section 9-1 Overview 9-1-1 Purpose of Chapter 9 This chapter gives an overview of Spare Parts available for the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e . Table 9-1 Contents in Chapter 9 Section Description Page Number 9-1 Overview 9-1 9-2 List of Abbreviations 9-1 9-3 Renewal Parts Lists 9-2 9-4 Operator Console Assy 9-3 9-5 LCD Assy 9-4 9-6 Keyboard Assy 9-6 9-7 Bottom Assy 9-7 9-8 Cables 9-15 9-9 Isolation Cart Components 9-16 9-10 Isolation Cart Enhanced Version Components 9-18 9-11 Accessories and Kits 9-21 9-12 Manuals 9-26 9-13 Probe 9-31 Section 9-2 List of Abbreviations • Assy - Assembly • Ctrl - Control • FRU 1 - Replacement part available in part hub • FRU 2 - Replacement part available from the manufacturer (lead time involved) • KBD - Keyboard • LCD - Liquid Crystal Display • BnV - Brightness and Volume • RX64- Dragon Front Processor Board • TMST - Master Board • TX64 - Dragon Transmit Board Chapter 9 Renewal Parts 9-1

[Page 190] Section 9-3Renewal Parts Lists 9-3-1 Equipment Models Covered in this Chapter Table 9-2 ACDC Power Pack & ACDC Power Cable list LOGIQ e Item Number Part Name Quantity FRU LOGIQ e Vet 001 5196783 ACDC adapter with clamp filter 1 1 x x x x 001A 5196783-2 ACDC adapter with clamp filter 1 1 x x x x 002 2409198 ACDC Power Pack unit 100W AC Adapter 1 1 x x x x 002A 2409198-2 ACDC Power Pack unit 110W AC Adapter 1 1 x x x x 003 5120411 ACDC Power Cable for USA 1 1 x x x x 004 5120412 ACDC Power Cable for Europe 1 1 x x x x 005 5120439 ACDC Power Cable for China 1 1 x x x x 006 5120440 ACDC Power Cable for Japan 1 1 x x x x 007 5125218 ACDC Power Cable for Australia/New Zealand 1 1 x x x x 008 5125219 ACDC Power Cable for United Kingdom and Ireland 1 1 x x x x 009 5125221 ACDC Power Cable for India/South Africa 1 1 x x x x 010 5125223 ACDC Power Cable for Argentina 1 1 x x x x 011 5125227 ACDC Power Cable for Israel 1 1 x x x x 012 5125228 ACDC Power Cable for Switzerland 1 1 x x x x 013 5400793 ACDC Power Cable for Brazil 1 1 x x x x 9-2 Section 9-3 - Renewal Parts Lists

[Page 191] Section 9-4 Operator Console Assy LCD Assy Keyboard Assy Bottom Assy Figure 9-1 OPERATOR CONSOLE ASSY Chapter 9 Renewal Parts 9-3

[Page 192] Section 9-5 LCD Assy 100 102 101 104 105 103 Figure 9-2 LCD Assy 9-4 Section 9-5 - LCD Assy

[Page 193] Section 9-5 LCD Assy (cont’d) Table 9-3 LCD Assy LCD Assy for LOGIQ e R5.0.x /LOGIQ e R5.2.x/LOGIQ e R6.x.x/ LOGIQ e Vet / 5244921 1 1 x x x Vivid e R4.x.x 5147473-2 LCD Assy for LOGIQ e R4.x.x/Vivid e R4.x.x 1 1 x x 5244918 LCD Assy for Vivid e R5.x.x / Vivid e R6.x.x 1 1 x 5190011 LCD Assy for LOGIQ i R4.x.x 1 1 x 5244920 LCD Assy for LOGIQ i R5.x.x 1 1 x 5419295 LCD Assy for LOGIQ e R7.x.x 1 1 x 5418452 LCD Front Cover for LOGIQ e R7.x.x 1 1 x LCD Front Cover for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x/ 5133509-3 1 1 x x x LOGIQ e R6.x.x /LOGIQ e Vet / Vivid e R4.x.x 5199553 LCD Front Cover for Vivid e R5.x.x / Vivid e R6.x.x 1 1 x 5190010-2 Front Cover for LOGIQ i R4.x.x /LOGIQ i R5.x.x 1 1 x 5419292 LCD Back Cover for LOGIQ e R7.x.x 1 1 x LCD Back Cover for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x/ 5149676 1 1 x x x LOGIQ e R6.x.x /LOGIQ e Vet / Vivid e R4.x.x 5212061 LCD Back Cover for Vivid e R5.x.x / Vivid e R6.x.x 1 1 x 5190008 Back Cover for LOGIQ i R4.x.x 1 1 x 5190009 Back Cover for LOGIQ i R5.x.x 1 1 x Inverter Assy LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ e R6.x.x /LOGIQ e Vet / 5147731-2 1 1 x x x Vivid e R5.x.x / Vivid e R6.x.x Inverter Assy for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i R4.x.x / 5147731 1 1 x x x x LOGIQ i R5.x.x LCD panel for LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ e R6.x.x / LOGIQ e Vet/ 5251801 1 2 x x x x Vivid e R4.x.x / Vivid e R5.x.x / Vivid e R6.x.x / LOGIQ i R5.x.x 5146747 LCD panel for LOGIQ e R4.x.x /Vivid e R4.x.x / LOGIQ i R4.x.x 1 2 x x x 105 5125944-3 LCD cable 1 2 x x x x 106 5184890 Cable Kit (LCD cable, KBD cables) for LOGIQ e R4.x.x / Vivid e R4.x.x 1 2 x x 106A 5184890-2 Cable Kit (LCD cable, KBD cables) for LOGIQ e R4.x.x / LOGIQ i R5.x.x 1 2 x x 107 5244561 Hg label for Vivid e R4.x.x 1 2 x 108 5366398 LCD Cable Kit (LCD Cable and LCD Cable with JAE connector 1 2 x x x x Chapter 9 Renewal Parts 9-5

[Page 194] Section 9-6Keyboard Assy 201 202 Figure 9-3 Keyboard Assy 9-6 Section 9-6 - Keyboard Assy

[Page 195] Section 9-6 Keyboard Assy (cont’d) Figure 9-4 Keyboard Assy (cont’d) Table 9-4 Keyboard Assy 5419297 Keyboard Assy for LOGIQ e R7.x.x 1 1 x 5198176 Keyboard Assy for LOGIQ e R5.0.x / LOGIQ e R5.2.x /LOGIQ e R6.x.x / LOGIQ e Vet 1 1 x x 5148753 Keyboard Assy for LOGIQ e R4.x.x 1 1 x 5172817 Keyboard Assy for Vivid e R4.x.x 1 1 x 5199342 Keyboard Assy Vivid e R5.x. x/ Vivid e R6.x.x 1 1 x 5184814 Keyboard Assy for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 1 x Chapter 9 Renewal Parts 9-7

[Page 196] Table 9-4 Keyboard Assy 201 5160471 Trackball Assy 1 1 x x x x 5420742 A/N Key Assy for LOGIQ e R7.x.x 1 2 x A/N Key Assy for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5123732 1 2 x x x LOGIQ e R6.x.x/ LOGIQ e Vet / LOGIQ i R4.x.x / LOGIQ i R5.x.x 5175936 A/N Key Assy for Vivid e R4.x.x 1 2 x 5252489 A/N Key Assy for Vivid e R5.x.x / Vivid e R6.x.x 1 2 x 5419296 Keyboard cover Assy for LOGIQ e R7.x.x 1 2 x Keyboard cover Assy for LOGIQ e R5.0.x / LOGIQ e R5.2.x /LOGIQ e R6.x.x/ 5199756 1 2 x x LOGIQ e Vet 5148760 Keyboard cover Assy for LOGIQ e R4.x.x 1 2 x 5173857 Keyboard cover Assy for Vivid e R4.x.x 1 2 x 5199973 Keyboard cover Assy for Vivid e R5.x.x / Vivid e R6.x.x 1 2 x 5190002 Keyboard cover Assy for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 2 x KBD cable kits for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ e 5154621-2 R6.x.x / LOGIQ e Vet /Vivid e R5.x.x / Vivid e R6.x.x /LOGIQ i R5.x.x 1 1 x x x x 5154621 KBD cable kits for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i R4.x.x 1 1 x x x Keyboard PWA kits for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ 5155123 1 1 x x x e R6.x.x / LOGIQ e Vet / LOGIQ i R4.x.x / LOGIQ i R5.x.x 5173672 Keyboard PWA kits for Vivid e R4.x.x 1 2 x 5224534 Keyboard PWA kits for Vivid e R5.x.x / Vivid e R6.x.x 1 1 x 206 5155004 Speaker Kits 2 1 x x x x 5125106-4 Main KBD to MST Cable for LOGIQ e R7.x.x 1 2 x 5125106-3 Main KBD to MST Cable 1 2 x x x x 9-8 Section 9-6 - Keyboard Assy

[Page 197] Section 9-7Bottom Assy 302 302A Figure 9-5 Bottom Assy Chapter 9 Renewal Parts 9-9

[Page 198] 306 308 309 310 Figure 9-6 Bottom Assy (cont’d) 9-10 Section 9-7 - Bottom Assy

[Page 199] 311 316 Figure 9-7 Bottom Assy (cont’d) Chapter 9 Renewal Parts 9-11

[Page 200] Bottom Cover Assy for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5422185 1 2 x x LOGIQ e R6.x.x / LOGIQ e R7.x.x / LOGIQ e Vet Bottom Cover Assy for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5148765 1 2 x x LOGIQ e R6.x.x/ LOGIQ e Vet 5148764 Bottom Cover Assy for Vivid e R4.x.x 1 2 x 5213129 Bottom Cover Assy for Vivid e R5.x.x / Vivid e R6.x.x 1 2 x 5182370 Bottom Cover Assy for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 2 x 2406640 TMST Board 1 1 x x x x 2406640-2 TMST Board 1 1 x x x x 2406640-3 TMST Board 1 1 x x x x 2406640-3R TMST Board 1 1 x x x x 2406640-4 TMST Board 1 1 x x x x TX64 Board for LOGIQ e R4.x.x / LOGIQ e R5.x.x / Vivid e R4.x.x / Vivid e 302 2404903 1 1 x x x x R5.x.x / LOGIQ i R4.x.x / LOGIQ i R5.x.x / LOGIQ e Vet TX64 Board for LOGIQ e R4.x.x / LOGIQ e R5.x.x / Vivid e R4.x.x / Vivid e 302A 2404903-2 1 1 x x x x R5.x.x / LOGIQ i R4.x.x / LOGIQ i R5.x.x / LOGIQ e Vet TX64 Board for LOGIQ e R4.x.x / LOGIQ e R5.x.x / Vivid e R4.x.x / Vivid e 302B 2404903-3 1 1 x x x x R5.x.x / LOGIQ i R4.x.x / LOGIQ i R5.x.x / LOGIQ e Vet 302C 2404903-6 TX64 Board for LOGIQ e R6.x.x / Vivid e R6.x.x 1 1 x x 302D 2404903-7 TX64 Board for LOGIQ e R6.x.x / LOGIQ e R7.x.x / Vivid e R6.x.x 1 1 x x 303 2404906 RX64 Board 1 1 x x x x 303A 2404906-3 RX64 Board 1 1 x x x x 304 5148771 Probe Connector Assy 1 1 x x x x 304A 5389034 Probe Connector Assy for LOGIQ e R6.x.x 1 1 x 304B 5422449 Probe Connector Assy for LOGIQ e R6.x.x / LOGIQ e R7.x.x 1 1 x 5124847-2 CWD Board 1 1 x x x x 5124847-3 CWD Board 1 1 x x x x 9-12 Section 9-7 - Bottom Assy

[Page 201] 5419298 Menu Panel Assy for LOGIQ e R7.x.x 1 1 x Menu Panel Assy for LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ e R6.x.x/ 5212013 1 1 x x LOGIQ e Vet 5148773 Menu Panel Assy for LOGIQ e R4.x.x / Vivid e R4.x.x 1 1 x x 5212340 Menu Panel Assy for Vivid e R5.x.x / Vivid e R6.x.x 1 1 x 5184871 Menu Panel Assy for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 1 x PM1.4G ETX CPU Module for LOGIQ e R4.x.x / LOGIQ e R5.x.x / Vivid e R4.x.x 307 5155175 1 1 x x x x / Vivid e R5.x.x / LOGIQ i R4.x.x / LOGIQ i R5.x.x / LOGIQ e Vet 5392210 U7500 CPU kits for LOGIQ e R6.x.x / Vivid e R6.x.x 1 1 x x 307A 5392210-2 U7500 CPU kits only for LOGIQ e R6.x.x / Vivid e R6.x.x 1 1 x x 308 5159620 512MB DDR Memory 1 1 x x x x Charger Board and Cable Kits for LOGIQ e R5.0.x / LOGIQ e R5.2.x /LOGIQ e 5162038-3 1 2 x x x x R6.x.x/ LOGIQ e Vet / Vivid e R5.x.x / Vivid e R6.x.x / LOGIQ i R5.x.x Charger Board and Cable Kits for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 5162038-2 1 2 x x x R4.x.x 5148768 Left FAN Assy (2 Fans) 1 1 x x x x 5173403-3 Right FAN Assy (2 Fans) 1 1 x x x x 311 5155166 LCD and Handle Hinge kits 1 1 x x x x 312 2406733 TMST2TX64 Assy 1 2 x x x x Handle Assy for LOGIQ e R4.x.x / LOGIQ e R5.0.x /LOGIQ e R5.2.X/LOGIQ e 5154937 1 2 x x x x R6.x.x / LOGIQ e Vet / Vivid e R4.x.x / LOGIQ i R4.x.x / LOGIQ i R5.x.x 5234933 Handle Assy for Vivid R5.x.x / Vivid e R6.x.x 1 2 x 314 5154486 Screw Kits 1 2 x x x x 315 5154731 Rubber Kits 1 2 x x x x 5255230 80G HDD without Program Assy 1 1 x x x x 5255231-2 160G HDD without Program Assy 1 1 x x x x 316 5148772 HDD Assy for LOGIQ e R4.x.x 1 1 x 5174862-5 HDD Assy for Vivid e R4.x.x 1 1 x 5190005 HDD Assy for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 1 x 317 5145407 CMOS Battery 1 1 x x x x Chapter 9 Renewal Parts 9-13

[Page 202] Battery Clip for LOGIQ e R5.0.x / LOGIQ e R5.2.x / LOGIQ e R6.x.x / LOGIQ e 5422180 1 2 x x x R7.x.x /LOGIQ e Vet / Vivid e R5.x.x / Vivid e R6.x.x Battery Clip for LOGIQ e R5.0.x / LOGIQ e R5.2.x //LOGIQ e R6.x.x LOGIQ e 5135311 1 2 x x x Vet / Vivid e R5.x.x / Vivid e R6.x.x 319 5234927 HDD Shelf kits for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 1 x 9-14 Section 9-7 - Bottom Assy

[Page 203] Section 9-8 Cables Chapter 9 Renewal Parts 9-15

[Page 204] Section 9-9Isolation Cart Components 507 509 Figure 9-8 Isolation Cart Components Table 9-6 Isolation Cart Components 501 5183729 Wheels 1 2 x x x x 5180439-2 Isolation transformer 110V 1 2 x x x x 502 5180376 Isolation transformer 200V~240V 1 2 x x x x 5180376-2 Isolation transformer 220V 1 2 x x x x 503 5183627 Handle kits 1 2 x x x x 504 5183958 Probe holder kits 1 2 x x x x 505 5183719 Hardware kits 1 2 x x x x 9-16 Section 9-9 - Isolation Cart Components

[Page 205] Table 9-6 Isolation Cart Components 5182671 USA class cable kits 1 2 x x x x 5182937 European class cable kits 1 2 x x x x 5182252 Chinese class cable kits 1 2 x x x x 5182323 Japanese class cable kits 1 2 x x x x 5182095 Australia/New Zealand class cable kits 1 2 x x x x 506 5182890 United Kingdom and Ireland class cable kits 1 2 x x x x 5182310 Denmark class cable kits 1 2 x x x x 5182038 India/South Africa class cable kits 1 2 x x x x 5182881 Argentina class cable kits 1 2 x x x x 5182625 Israel class cable kits 1 2 x x x x 5182631 Switzerland class cable kits 1 2 x x x x 507 5183906 Security lock 1 2 x x x x 5176271-2 Isolation Cart (110V) 1 2 x x x x 5177329-2 Isolation Cart (220V) 1 2 x x x x 509 5195546 Isolation Cart 250V T 5A Fuse for Tranformer 1 1 x x x x Chapter 9 Renewal Parts 9-17

[Page 206] Section 9-10 Isolation Cart Enhanced Version Components 511 512 521 524 Figure 9-9 Isolation Cart Components 9-18 Section 9-10 - Isolation Cart Enhanced Version Components

[Page 207] Table 9-7 Isolation Cart Components 5384810 Isolation Cart (110V) 1 2 x x x x 5423269 Isolation Cart (110V) 1 2 x x x x 5384811 Isolation Cart (220V) 1 2 x x x x 5423270 Isolation Cart (220V) 1 2 x x x x 511 5394023 Castor kits 1 2 x x x x 512 5391829 Gas Spring lever 5394060 Isolation cart transformer 110V (Dark Steel Blue) 1 2 x x x x 5394061 Isolation cart transformer 220V (Dark Steel Blue) 5426649 Isolation cart transformer 110V (Onyx Black) 1 2 x x x x 513A 5426650 Isolation cart transformer 220V (Onyx Black) 514 5394028 Cable hook kit (Dark Steel Blue) 1 2 x x x x 514A 5426642 Cable hook kit (Onyx Black) 1 2 x x x x 515 5394065 Isolation Cart Rear Handle 1 2 x x x x 516 5391606 Spring Cable Assy 1 2 x x x x 517 5394036 Locate block and Screw cap (GE Pearl Metallic) 1 2 x x x x 517A 5426645 Locate block and Screw cap (GE N9) 1 2 x x x x 518 5394032 Probe and gel holder kit (Dark Steel Blue) 1 2 x x x x 518A 5426644 Probe and gel holder kit (Onyx Black) 1 2 x x x x 519 5394021 Handle clip kit 1 2 x x x x 521 5215494 Security lock with package 1 2 x x x x 522 5394064 Isolation Cart Front handle (Dark Steel Blue) 1 2 x x x x 522A 5426643 Isolation Cart Front handle (Onyx Black) 1 2 x x x x 523 5394067 Gas Spring Assy (Dark Steel Blue) 1 2 x x x x 523A 5426646 Gas Spring Assy (Onyx Black) 1 2 x x x x Chapter 9 Renewal Parts 9-19

[Page 208] Table 9-7 Isolation Cart Components 5177154 AC Power Cord Switzerland 1 2 x x x x 5176753 AC Power Cord Israel 1 2 x x x x 5177195 AC Power Cord Argentina 1 2 x x x x 5176773 AC Power Cord India 1 2 x x x x 5177153 AC Power Cord Denmark 1 2 x x x x 524 5176907 AC Power Cord UK 1 2 x x x x 5177187-2 AC Power Cord Australia 1 2 x x x x 5177126 AC Power Cord Japan 1 2 x x x x 5176304 AC Power Cord China 1 2 x x x x 5177123 AC Power Cord Europe 1 2 x x x x 5177146 AC Power Cord USA 1 2 x x x x 525 5393025 Isolation Cart Drawer Kits (GE Pearl Metallic) 1 2 x x x x 525A 5426647 Isolation Cart Drawer Kits (GE N9) 1 2 x x x x 526 5393026 Isolation Cart Basket Kits (GE Pearl Metallic) 1 2 x x x x 526A 5426648 Isolation Cart Basket Kits (GE N9) 1 2 x x x x 9-20 Section 9-10 - Isolation Cart Enhanced Version Components

[Page 209] Section 9-11 Accessories and Kits Battery Pack for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5422172 LOGIQ e R6.x.x / LOGIQ e R7.x.x / LOGIQ e Vet /Vivid e R4.x.x / LOGIQ 1 2 x x x x i R4.x.x Battery Pack for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5120410-2 1 2 x x x x 601 LOGIQ e R6.x.x/LOGIQ e Vet /Vivid e R4.x.x / LOGIQ i R4.x.x Battery Pack for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x / 5120410 1 2 x x x x LOGIQ e R6.x.x/LOGIQ e Vet /Vivid e R4.x.x / LOGIQ i R4.x.x 5183459 Battery Pack Vivid e R5.x.x / Vivid e R6.x.x / LOGIQ i R5.x.x 1 2 x x DVD-RW (USA) LG DVD-RW for LOGIQ e R4.x.x / Vivid e R4.x.x 602 5151233 1 2 x x x / LOGIQ i R4.x.x 602A 5151233-2 DVD-RW (USA) LITEON DVD-RW 1 2 x x x x 602B 5151233-3 DVD-RW (USA) LITEON DVD-RW 1 2 x x x x 602C 5151233-4 DVD-RW (USA) LITEON DVD-RW 1 2 x x x x DVD-RW (CHN) LG DVD-RW LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 603 5151255 1 2 x x x R4.x.x 603A 5151255-2 DVD-RW (CHN) LITEON DVD-RW 1 2 x x x x 603B 5151255-3 DVD-RW (CHN) LITEON DVD-RW 1 2 x x x x 603C 5151255-4 DVD-RW (CHN) LITEON DVD-RW 1 2 x x x x DVD-RW (EUR) LG DVD-RW LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 604 5151234 1 2 x x x R4.x.x 604A 5151234-2 DVD-RW (EUR) LITEON DVD-RW 1 2 x x x x 604B 5151234-3 DVD-RW (EUR) LITEON DVD-RW 1 2 x x x x 604C 5151234-4 DVD-RW (EUR) LITEON DVD-RW 1 2 x x x x 605 5182891-2 DVD-RW (JPN) LITEON DVD-RW 1 2 x x x x 605A 5182891-3 DVD-RW (JPN) LITEON DVD-RW 1 2 x x x x 605B 5182891-4 DVD-RW (JPN) LITEON DVD-RW 1 2 x x x x 606 5151236 USB Footswitch 3 Pedal Footswitch 1 2 x x x x 607 2327703 USB Footswitch FSU 2001 1 Pedal Footswitch 1 2 x x x 607A 5338419 USB Footswitch FSU-1000 1 2 x x x 608 5172876-2 USB Wireless Card 1 2 x x x x Chapter 9 Renewal Parts 9-21

[Page 210] 609 5151259 UP-D897 Digital B/W Printer (USA) 1 2 x x x x 610 5151261 UP-D897 Digital B/W Printer (EU) 1 2 x x x x 611 5151262 UP-D897 Digital B/W Printer (CHN) 1 2 x x x x 612 5151263 UP-D897 Digital B/W Printer (JPN) 1 2 x x x x 613 5133107 UP-D23MD Digital Color Printer (US) 1 2 x x x x 614 5133108 UP-D23MD Digital Color Printer (EU) 1 2 x x x x 615 5133106 UP-D23MD Digital Color Printer (CN) 1 2 x x x x 616 5133109 UP-D23MD Digital Color Printer (JP) 1 2 x x x x 613A 5133107-2 UP-D25MD Digital Color Printer (US) 1 2 x x x x 614A 5133108-2 UP-D25MD Digital Color Printer (EU) 1 2 x x x x 615A 5133106-2 UP-D25MD Digital Color Printer (CN) 1 2 x x x x 616A 5133109-2 UP-D25MD Digital Color Printer (JP) 1 2 x x x x 617 5175689 HP470 Printer Kits (HP470+PIT) -US 1 2 x x x x 618 5175988 HP470 Printer Kits (HP470+PIT) -EU 1 2 x x x x 619 5175350 HP470 Printer Kits (HP470+PIT) -CN 1 2 x x x x 620 5175546 HP470 Printer Kits (HP470+PIT) -JP 1 2 x x x x HP K550 PC Printer -US for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 621 5175122 1 2 x x x R4.x.x 621A 5175122-2 HP K5400 PC Printer -US 1 2 x x x x 621B 5175122-3 HP K8600 PC Printer -US 1 2 x x x x HP K550 PC Printer -EU for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 622 5175833 1 2 x x x R4.x.x 622A 5175833-2 HP K5400 PC Printer -EU 1 2 x x x x 622B 5175833-3 HP K8600 PC Printer -EU 1 2 x x x x HP K550 PC Printer -CN for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 623 5175554 1 2 x x x R4.x.x 623A 5175554-2 HP K5400 PC Printer -CN 1 2 x x x x 623B 5175554-3 HP K8600 PC Printer -CN 1 2 x x x x HP K550 PC Printer-JP for LOGIQ e R4.x.x / Vivid e R4.x.x / LOGIQ i 624 5175898 1 2 x x x R4.x.x 624A 5175898-2 HP K5400 PC Printer-JP 1 2 x x x x 9-22 Section 9-11 - Accessories and Kits

[Page 211] 624B 5175898-3 HP K8600 PC Printer-JP 1 2 x x x x Loop Connector service tool for channel diagnostic used for LOGIQ e 625 5183418 R5.0.x / LOGIQ e R5.2.x/LOGIQ e R6.x.x / LOGIQ e Vet / Vivid e R5.x.x/ 1 2 x x x x Vivid e R6.x.x/ LOGIQ i R4.x.x / LOGIQ i R5.x.x 626 5146055 ECG USB Cable 1 2 x x x x ECG Module from Norav Isral ECG Module, not for applicable for Muslim 627 5129487 1 2 x x x x countries and China 628 5146056 ECG Detachable Cable AHA 1 2 x x x x 629 5146739 ECG Detachable Cable IEC 1 2 x x x x 630 5149641 ECG Module with Chinese Label 1 2 x x x x 631 5195563 ECG Module with SKD Label, only applicable for Muslim countries 1 2 x x x x 632 5184951 USB Hub 1 2 x x x x 632A 5184951-2 4 Ports HUB (USB 2.0) 1 2 x x x x 633 5168040 USB Memory 512M 1 2 x x x x 633A 5168040-2 USB Memory 1G 1 2 x x x x 633B 5168040-3 USB Memory 2G 1 2 x x x x 633C 5168040-4 USB Memory 4G 1 2 x x x x LOGO Kit for LOGIQ e R4.x.x / LOGIQ e R5.0.x / LOGIQ e R5.2.x/LOGIQ 5181598 1 2 x e R6.x.x 5234932 LOGO Kit for LOGIQ e Vet 1 2 x 5183684 LOGO Kit for Vivid e R4.x.x 1 2 x 5183684 LOGO Kit for Vivid e R5.x.x / Vivid e R6.x.x 1 2 x 5191678 LOGO Kit for LOGIQ i R4.x.x / LOGIQ i R5.x.x 1 2 x 635 5173797 USB Harddisk 40G 1 2 x x x 635A 5173797-2 USB Harddisk 80G 1 2 x x x 635B 5173797-3 USB Harddisk 250G 1 2 x x x 635C 5173797-4 USB Harddisk 500G 1 2 x x x 636 5322237 Barcode Reader 4600G for LOGIQ e R5.2.x/LOGIQ e R6.x.x 1 2 x 637 5322752 Barcode Reader 3800G for LOGIQ e R5.2.x/LOGIQ e R6.x.x 1 2 x 638 5322231 Barcode Reader Cable for Service for LOGIQ e R5.2.x/LOGIQ e R6.x.x 1 2 x 639 5324784 3-meter Internet Cable for Service 1 2 x x x x Chapter 9 Renewal Parts 9-23

[Page 212] 640 5199293 Shoulder Bag 1 2 x x x x 641 5196495 Clamp Filter for LOGIQ i R5.1.x 1 2 x 642 5268864 Peripheral Driver Patch CD Installation kit 1 2 x x x x 643 5248284 Software Upgrade DVD for R5.1.0 for LOGIQ i 1 2 x 644 5264324 USB Wireless adapter WG111v3 Installation kit 1 2 x x x x 644A 5264324-2 USB Wireless adapter WN111v2 Installation kit 1 2 x x x x 645 5172876-3 NetGear USB Wireless Adapter WG111 V3 1 2 x x x x 646 5324784 3m Lan Cable 1 2 x x x x 5173474 System and Application software DVD for LOGIQ e (R4.0.0) 1 2 x 5173474-2 System and Application software DVD for LOGIQ e (R4.0.1) 1 2 x 5173474-3 System and Application software DVD for LOGIQ e (R4.0.2) 1 2 x 5173474-4 System and Application software DVD for LOGIQ e (R4.0.3) 1 2 x 5173474-5 System and Application software DVD for LOGIQ e (R4.0.4) 1 2 x 5173474-6 System and Application software DVD for LOGIQ e (R4.0.4) 1 2 x 5235031 System and Application software DVD for LOGIQ e (R 5.0.0) 1 2 x 648 5235031-2 System and Application software DVD for LOGIQ e (R 5.0.1) 1 2 x 5235031-3 System and Application software DVD for LOGIQ e (R 5.0.1) 1 2 x 5322236 System and Application software DVD for LOGIQ e (R 5.2.0) 1 2 x 5322457-4 System and Application software DVD for LOGIQ e (R 5.2.1) 1 2 x 5322457-6 System and Application software DVD for LOGIQ e (R 5.2.2) 1 2 x 5322457-7 System and Application software DVD for LOGIQ e (R 5.2.3) 1 2 x 5396928-3 System and Application software DVD for LOGIQ e (R 6.0.1) 1 2 x 5396928-4 System and Application software DVD for LOGIQ e (R 6.0.2) 1 2 x 5396928-5 System and Application software DVD for LOGIQ e (R 6.0.3) 1 2 x 5396928-6 System and Application software DVD for LOGIQ e (R 6.0.4) 1 2 x 655 5423626 System and Application software DVD for LOGIQ e (R 7.0.0) 1 2 x 5248829 System and Application software DVD for LOGIQ e Vet (R 5.0.0) 1 2 x 651 5248829-2 System and Application software DVD for LOGIQ e Vet (R 5.0.1) 1 2 x 5248829-3 System and Application software DVD for LOGIQ e Vet (R 5.0.1) 1 2 x 9-24 Section 9-11 - Accessories and Kits

[Page 213] 5248829-4 System and Application software DVD for LOGIQ e Vet (R 5.2.0) 1 2 x 5248829-5 System and Application software DVD for LOGIQ e Vet (R 6.0.3) 1 2 x 5175298 System and Application software DVD for Vivid e (R4.0.0) x 5175298-2 System and Application software DVD for Vivid e (R4.0.1) x 5175298-3 System and Application software DVD for Vivid e (R4.0.2) x 5175298-4 System and Application software DVD for Vivid e (R4.0.3) x 5175298-5 System and Application software DVD for Vivid e (R4.0.4) x 5175298-6 System and Application software DVD for Vivid e (R4.0.4) x 5248828 System and Application software DVD for Vivid e (R 5.0.0) x 5248828-2 System and Application software DVD for Vivid e (R 5.0.1) x 5248828-3 System and Application software DVD for Vivid e (R 5.0.1) x 5248828-4 System and Application software DVD for Vivid e (R 5.2.0) x 5248828-5 System and Application software DVD for Vivid e (R 5.2.1) x 5248828-6 System and Application software DVD for Vivid e (R 6.0.0) x 5191713-3 System and Application software DVD for LOGIQ i (R4.1.1) x 654 5191713-6 System and Application software DVD for LOGIQ i (R5.1.0) x 5191713-7 System and Application software DVD for LOGIQ i (R5.1.1) x Chapter 9 Renewal Parts 9-25

[Page 214] Section 9-12Manuals Table 9-9 MANUALS for LOGIQ e R4.x.x 5370626 -100 Service Manual 1 N LOGIQ e R4.x.x User Manual, English 5118586-100 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, French 5118586-101 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, Spanish 5118586-106 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, German 5118586-108 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, Italian 5118586-111 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, Portuguese 5118586-127 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, Japanese 5118586-140 Basic User Manual 1 N LOGIQ e R4.x.x User Manual, Chinese 5118586-141 Basic User Manual 1 N LOGIQ e R4.x.x Quick Start Guide, English 5130174 -100 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, French 5130174 -101 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, Spanish 5130174 -106 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, German 5130174 -108 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, Italian 5130174 -111 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, Portuguese 5130174 -127 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, Japanese 5130174 -140 Quick Start Guide 1 N LOGIQ e R4.x.x Quick Start Guide, Chinese 5130174 -141 Quick Start Guide 1 N LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e 5370626 -100 Service Manual 1 N Service Manual LOGIQ e User Manual, English 5199656 -100 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, French 5199656 -101 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, Spanish 5199656 -106 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, German 5199656 -108 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, Italian 5199656 -111 Basic User Manual (for R5.0.x) 1 N 9-26 Section 9-12 - Manuals

[Page 215] LOGIQ e User Manual, Portuguese 5199656 -127 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, Japanese 5199656 -140 Basic User Manual (for R5.0.x) 1 N LOGIQ e User Manual, Chinese 5199656 -141 Basic User Manual (for R5.0.x) 1 N LOGIQ e Vet User Manual English 5198506 -100 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, French 5198506 -101 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, Spanish 5198506 -106 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, German 5198506 -108 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, Italian 5198506 -111 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, Portuguese 5198506 -127 Basic User Manual (for R5.0.x/5.2.x) 1 N LOGIQ e Vet User Manual, Japanese 5198506 -140 Basic User Manual (for R5.0.x) 1 N LOGIQ e Vet User Manual, Chinese 5198506 -141 Basic User Manual (for R5.0.x) 1 N LOGIQ e R5.0.x CKD User Manual, 5268200-100 Basic User Manual (for R5.0.x) 1 N English LOGIQ e User Manual, English 5314622 -100 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, French 5314622 -101 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, Spanish 5314622 -106 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, German 5314622 -108 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, Italian 5314622 -111 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, Portuguese 5314622 -127 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, Japanese 5314622 -140 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e User Manual, Chinese 5314622 -141 Basic User Manual (for R5.2.x/R6.x.x) 1 N LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -100 Quick Start Guide (for R5.0.x) 1 N Start Guide, English LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -101 Quick Start Guide (for R5.0.x) 1 N Start Guide, French LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -106 Quick Start Guide (for R5.0.x) 1 N Start Guide, Spanish LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -108 Quick Start Guide (for R5.0.x) 1 N Start Guide, German LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -111 Quick Start Guide (for R5.0.x) 1 N Start Guide, Italian LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -127 Quick Start Guide (for R5.0.x) 1 N Start Guide, Portuguese Chapter 9 Renewal Parts 9-27

[Page 216] LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -140 Quick Start Guide (for R5.0.x) 1 N Start Guide, Japanese LOGIQ e R5.0.x / LOGIQ e Vet Quick 5212024 -141 Quick Start Guide (for R5.0.x) 1 N Start Guide, Chinese LOGIQ e R5.2.x/R6.x.x Quick Start 5314624-100 Quick Start Guide (for R5.2.x/R6.x.x) 1 N Guide LOGIQ e Vet R5.2.x Quick Start Guide, 5329881-100 Quick Start Guide (for R5.2.x) 1 N English Table 9-11 MANUALS for Vivid e R4.x.x 5370626 -100 Service Manual 1 N Vivid e R4.x.x User Manual, English 5165247-100 Basic User Manual 1 N Vivid e R4.x.x User Manual, French 5165247-101 Basic User Manual 1 N Vivid e R4.x.x User Manual, Spanish 5165247-106 Basic User Manual 1 N Vivid e R4.x.x User Manual, German 5165247-108 Basic User Manual 1 N Vivid e R4.x.x User Manual, Italian 5165247-111 Basic User Manual 1 N Vivid e R4.x.x User Manual, Portuguese 5165247-127 Basic User Manual 1 N Vivid e R4.x.x User Manual, Japanese 5165247-140 Basic User Manual 1 N Vivid e R4.x.x User Manual, Chinese 5165247-141 Basic User Manual 1 N Vivid e R4.x.x Quick Start Guide, English 5175726 -100 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, French 5175726 -101 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, Spanish 5175726 -106 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, German 5175726 -108 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, Italian 5175726 -111 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, Portuguese 5175726 -127 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, Japanese 5175726 -140 Quick Start Guide 1 N Vivid e R4.x.x Quick Start Guide, Chinese 5175726 -141 Quick Start Guide 1 N 9-28 Section 9-12 - Manuals

[Page 217] Table 9-12 MANUALS for Vivid e R5.x.x / Vivid e R6.x.x 5370626-100 Service Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, English 5198874 -100 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, French 5198874 -101 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, Spanish 5198874 -106 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, German 5198874 -108 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, Italian 5198874 -111 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, Portuguese 5198874 -127 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, Japanese 5198874 -140 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x User Manual, Chinese 5198874 -141 Basic User Manual 1 N Vivid e R5.x.x/R6.x.x Quick Start Guide, English 5212811 -100 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, French 5212811 -101 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, Spanish 5212811 -106 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, German 5212811 -108 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, Italian 5212811 -111 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, Portuguese 5212811 -127 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, Japanese 5212811 -140 Quick Start Guide 1 N Vivid e R5.0.x Quick Start Guide, Chinese 5212811 -141 Quick Start Guide 1 N Table 9-13 MANUALS for LOGIQ i R4.x.x / LOGIQ i R5.x.x Manuals 5370626-100 Service Manual 1 N LOGIQ i R4.x.x User Manual, English 5179205-100 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, French 5179205-101 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, Spanish 5179205-106 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, German 5179205-108 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, Italian 5179205-111 Basic User Manual 1 N Chapter 9 Renewal Parts 9-29

[Page 218] Table 9-13 MANUALS for LOGIQ i R4.x.x / LOGIQ i R5.x.x LOGIQ i R4.x.x User Manual, Portuguese 5179205-127 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, Japanese 5179205-140 Basic User Manual 1 N LOGIQ i R4.x.x User Manual, Chinese 5179205-141 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, English 5212229-100 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, French 5212229-101 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, Spanish 5212229-106 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, German 5212229-108 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, Italian 5212229-111 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, Portuguese 5212229-127 Basic User Manual 1 N LOGIQ i R5.x.x User Manual, Chinese 5179205-141 Basic User Manual 1 N LOGIQ i R4.x.x Quick Start Guide, English 5180949 -100 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, French 5180949 -101 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, Spanish 5180949 -106 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, German 5180949 -108 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, Italian 5180949 -111 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, Portuguese 5180949 -127 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, Japanese 5180949 -140 Quick Start Guide 1 N LOGIQ i R4.x.x Quick Start Guide, Chinese 5180949 -141 Quick Start Guide 1 N LOGIQ i R5.x.x Quick Start Guide, English 5245368 -100 Quick Start Guide 1 N 9-30 Section 9-12 - Manuals

[Page 219] Section 9-13Probe Table 9-14 Probes for LOGIQ e, Vivid e and LOGIQ i Quality Part Part Item Name Number Description LOGIQ e R4.x.x LOGIQ e R5.0.x LOGIQ e R5.2.x LOGIQ e R6.x.x LOGIQ e R7.x.x Vivid e R4.x.x Vivid e R5.0.x Vivid e R5.2.x Vivid e R6.x.x LOGIQ i R4.x.x LOGIQ i R5.x.x Probe 701 4C-RS 5131629 1 1 x x x x x x x x x x (Center Frequency: 3.2MHz) Probe 702 E8C-RS 2290777 1 1 x x x x x x x x (Center Frequency: 6.5MHz) Probe 703 8C-RS 2354971 1 1 x x x x x x x x x (Center Frequency: 6.5MHz) Probe 704 i12L-RS 2377942 1 1 x x x x x x x x x x (Center Frequency: 5.6MHz) Probe 705 8L-RS 2376127 1 1 x x x x x x x x x x (Center Frequency: 6.2MHz) Probe 706 3S-RS 2355686 1 1 x x x x x x x x x x (Center Frequency: 2.0MHz) Probe 707 12L-RS 5154514 1 1 x x x x x x x x (Center Frequency: 7.5MHz) Probe 708 i739-RS 2404995 1 1 x x x x (Center Frequency: 7.4MHz) Probe 709 T739-RS 2404999 1 1 x x x x (Center Frequency: 6.5MHz) Probe 710 P2D KE100003 1 1 x x x x (Center Frequency:2.0MHz) Probe 711 9L-RS 5213143 1 1 x x x x x x x (Center Frequency: 7.5MHz) Probe 712 6S-RS 47236867 1 1 x x x x (Center Frequency: 4.8MHz) Probe 713 16L-RS 5317271 1 1 x x (Center Frequency: 12.0MHz) Probe 714 6Tc-RS KN100104 x x (Center Frequency: 4.8MHz) Probe 715 L8-18i-RS 5397810 x (Center Frequency: 9.5MHz) NOTE: 16L-RS is not available in China. Chapter 9 Renewal Parts 9-31

[Page 220] Section 9-13 Probe (cont’d) Table 9-15 Probes for LOGIQ e Vet Quantity Part Item Part Name Number Description LOGIQ e Vet R5.0.x LOGIQ e Vet R5.2.x LOGIQ e Vet R5.2.x 750 4C-RS Vet 5198378 Probe (Center Frequency: 3.2MHz) 1 1 x x x 751 E8C-RS Vet 5134643 Probe (Center Frequency: 6.5MHz) 1 1 x x x 752 8C-RS Vet 5134642 Probe (Center Frequency: 6.5MHz) 1 1 x x x 753 i12L-RS Vet 5134645 Probe (Center Frequency: 5.6MHz) 1 1 x x x 754 8L-RS Vet 2376127 Probe (Center Frequency: 6.2MHz) 1 1 x x x 755 3S-RS Vet 5134647 Probe (Center Frequency: 2.0MHz) 1 1 x x x 756 12L-RS Vet 5212304 Probe (Center Frequency: 7.5MHz) 1 1 x x x 757 9L-RS Vet 5220453 Probe (Center Frequency: 7.5MHz) 1 1 x x x 758 i739-RS-LC 5136420 Probe (Center Frequency: 6.4MHz) 1 1 x x 759 6S Vet-RS Vet 5198571 Probe (Center Frequency:4.8MHz) 1 1 x x 760 6Tc-RS Vet 5430790 Probe (Center Frequency: 4.8 MHz) 1 1 x x 9-32 Section 9-13 - Probe

[Page 221] Chapter 10 Care & Maintenance Section 10-1 Overview 10-1-1 Periodic Maintenance Inspections It has been determined by engineering that your LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e system does not have any high wear components that fail with use, therefore no Periodic Maintenance Inspections are mandatory. Some Customers Quality Assurance Programs may require additional tasks and or inspections at a different frequency than listed in this manual. 10-1-2 Purpose of Chapter 10 This chapter describes Care & Maintenance on the scanner and peripherals. These procedures are intended to maintain the quality of the ultrasound systems performance . Read this chapter completely and familiarize yourself with the procedures before performing a task. Table 10-1 Contents in Chapter 10 Section Description Page Number 10-1 Overview 10-1 10-2 Why do Maintenance 10-2 10-3 Maintenance Task Schedule 10-2 10-4 Tools Required 10-4 10-5 System Maintenance 10-5 10-6 Electrical Safety Tests 10-11 10-7 When There's Too Much Leakage Current... 10-18 CAUTION Practice good ESD prevention. Wear an anti–static strap when handling electronic parts and even when disconnecting/connecting cables. DANGER BE SURE TO DISCONNECT THE SYSTEM POWER PLUG BEFORE YOU REMOVE ANY PARTS. BE CAUTIOUS WHENEVER POWER IS STILL ON AND COVERS ARE REMOVED. CAUTION Do not pull out or insert circuit boards while power is ON. CAUTION Do not operate this unit unless all board covers and frame panels are securely in place. System performance and cooling require this. Chapter 10 Care & Maintenance 10-1

[Page 222] Section 10-2 Why do Maintenance 10-2-1 Keeping Records It is good business practice that ultrasound facilities maintain records of periodic and corrective maintenance. The Ultrasound Periodic Maintenance Inspection Certificate provides the customer with documentation that the ultrasound scanner is maintained on a periodic basis. A copy of the Ultrasound Periodic Maintenance Inspection Certificate should be kept in the same room or near the scanner. 10-2-2 Quality Assurance In order to gain accreditation from organizations such as the American College of Radiology (USA), it is the customer’s responsibility to have a quality assurance program in place for each scanner. The program must be directed by a medical physicists, the supervising radiologist/physician or appropriate designee. Routine quality control testing must occur regularly. The same tests are performed during each period so that changes can be monitored over time and effective corrective action can be taken. Testing results, corrective action and the effects of corrective action must be documented and maintained on the site. Your GE service representative can help you with establishing, performing and maintaining records for a quality assurance program. Please contact us for coverage information and/or price for service. Section 10-3 Maintenance Task Schedule 10-3-1 How often should care & maintenance tasks be performed? The Care & Maintenance Task Schedule (provided on page 10-3) specifies how often your LOGIQ e/ LOGIQ e Vet/LOGIQ i/Vivid e should be serviced and outlines items requiring special attention. NOTE: It is the customer’s responsibility to ensure the LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e care & maintenance is performed as scheduled in order to retain its high level of safety, dependability and performance. Your GE Service Representative has an in-depth knowlegde of your LOGIQ e/LOGIQ e Vet/LOGIQ i/ Vivid e ultrasound scanning system and can best provide competent, efficient service. Please contact us for coverage information and/or price for service. The service procedures and recommended intervals shown in the Care & Maintenance Task Schedule assumes that you use your LOGIQ e/LOGIQ e Vet/LOGIQ i/Vivid e for an average patient load (10-12 per day) and use it as a primary mobile unit which is transported between diagnostic facilities. NOTE: If conditions exist which exceed typical usage and patient load, then it is recommended to increase the maintenance frequencies. 10-2 Section 10-2 - Why do Maintenance

[Page 223] Table 10-2 Customer Care Schedule Per Facilities Service at Indicated Time Daily Weekly Monthly QA Program Notes Clean Probes •* * or before each use Inspect AC Mains Cable • Mobile Unit Check Weekly Inspect Cables and Connectors • Clean Console • Clean LCD • Twice Console Leakage Current Checks See Note Annually Twice Peripheral Leakage Current Checks See Note Annually Twice Surface Probe Leakage Current Checks See Note Annually Endocavity Probe Leakage Quarterly See Note Current Checks Annually Twice Measurement Accuracy Checks See Note Annually NOTE: May require specialized equipment to complete NOTE: PMs are not mandatory, the table above is for reference only. Chapter 10 Care & Maintenance 10-3

[Page 224] Section 10-4 Tools Required 10-4-1 Special Tools, Supplies and Equipment 10-4-1-1 Specific Requirements for Care & Maintenance Table 10-3 Overview of Requirements for Care & Maintenance Tool Part Number Comments Digital Volt Meter (DVM) 46–194427P231 Kit includes anti–static mat, wrist strap and cables for 200 to 240 46–194427P279 V system Anti Static Kit 46–194427P369 3M #2204 Large adjustable wrist strap 46–194427P373 3M #2214 Small adjustable wrist strap 46–194427P370 3M #3051 conductive ground cord 46–194427P278 120V Anti Static Vacuum Cleaner 46–194427P279 230V The satety Analyzer tool should be calibrated abd compliant with Safety Analyzer 46–285652G1 AAMI/ESI 1993 or IEC 60601 or AS/NZS 3551. QIQ Phantom E8370RB RMI Grayscale Target Model 403GS B/W Printer Cleaning Sheet See printer user manual for requirements Color Printer Cleaning Sheet See printer user manual for requirements Disposable Gloves 10-4 Section 10-4 - Tools Required

[Page 225] Section 10-5 System Maintenance 10-5-1 Preliminary Checks The preliminary checks take about 15 minutes to perform. Refer to the system user documentation whenever necessary. Table 10-4 System Checks 1 Ask & Listen Ask the customer if they have any problems or questions about the equipment. Fill in the top of the Ultrasound Inspection Certificate (see page 19). Note all probes and system 2 Paperwork options. With AC input. Turn the system power on and verify that all fans and peripherals turn on. Watch the displays during 3 Power up power up to verify that no warning or error messages are displayed. Check the Battery recharging. Without AC input, use internal battery. 4 Probes Verify that the system properly recognizes all probes. 5 Displays Verify proper display on the LCD. 6 Presets Backup all customer presets on an DVD-RW. Chapter 10 Care & Maintenance 10-5

[Page 226] 10-5-2 Functional Checks (See Also Chapter 4) The functional checks take about 60 minutes to perform. Refer to the system user documentation whenever necessary. 10-5-2-1 System Checks Table 10-5 System Functional Checks ÷ Step Description Verify basic B-Mode (2D) operation. Check the basic system controls that affect this mode of B-Mode operation. Verify basic CF-Mode (Color Flow Mode) operation. Check the basic system controls that affect this CF-Mode mode of operation. Verify basic Doppler operation (PW if available). Check the basic system controls that affect this mode Doppler Modes of operation. M-Mode Verify basic M-Mode operation. Check the basic system controls that affect this mode of operation. *Applicable Verify the basic operation of all optional modes such as Multi-Image, 3D, Harmonics, Cine,... etc. Software Options Check the basic system controls that affect each options operation. Xmit/Recv Use the Visual Channel Utility on the loop connect to verify that all system xmit/recv channels are Elements functional. Keyboard Test Perform the Keyboard Test Procedure to verify that all keyboard controls are OK. LCD Verify basic LCD display functions. Refer to Chapter 3 of the User Manual. Software Menu Verify Software Menu display functions. Refer to Chapter 3 of the User Manual. check In measurement mode, make distance measurement, get result in result window. Verify the distance Measurements by graduate rule. Distance Accuracy should be within ± 5%. (Name result from result window Result A, result from graduate rule Result B; Distance Accuracy= (Result B-Result A)/Result A) NOTE: * Some software may be considered standard depending upon system model configuration. 10-6 Section 10-5 - System Maintenance

[Page 227] 10-5-2-2 Peripheral/Option Checks If any peripherals or options are not part of the system configuration, the check can be omitted. Refer to the User Manual for a list of approved peripherals/options. Table 10-6 GE Approved Peripheral/Hardware Option Functional Checks 1 B/W Printer Verify hardcopy output of the B/W video page printer. Clean heads and covers if necessary. 2 Color Printer Verify hardcopy output of the Color video page printer. Clean heads and covers if necessary. 3 DICOM Verify that DICOM is functioning properly. Send an image to a DICOM device. 4 Footswitch Verify that the footswitch is functioning as programed. Clean as necessary. 5 ECG Verify basic operation with customer. 6 DVD Verify that the DVD is functioning properly. Clean heads and covers if necessary. 10-5-3 Input Power 10-5-3-1 AC/DC Adapter Inspection Table 10-7 AC/DC Adapter Inspection 1 Unplug Cord Disconnect the mains cable from the wall and system. 2 Inspect Inspect it and its connectors for damage of any kinds. Verify that the LINE wires are properly attached to the terminals, and that no strands may cause a short 3 Verify circuit. 10-5-4 Cleaning 10-5-4-1 General Cleaning Table 10-8 General Cleaning Remove the battery. Use a fluid detergent in warm water on a soft, damp cloth to carefully wipe the entire 1 Console system. Be careful not to get the cloth too wet so that moisture does not enter the console. 2 Probe Holder Clean probe holders. (they may need to be soaked to remove excess gel). Use a soft, non-abrasive folder cloth. Gently wipe the LCD face. DO NOT use a glass cleaner that has a 3 LCD hydrocarbon base (such as Benzene, Methy Alcohol or Methy Ethyl Ketone) on LCD with the filter (anti- glare shield). Chapter 10 Care & Maintenance 10-7

[Page 228] 10-5-5 Physical Inspection Table 10-9 Physical Checks Verify that all system labeling is present and in readable condition. Refer to User Manual, for 1 Labeling details. 2 Scratches & Dents Inspect the console for dents, scratches or cracks. 3 Control Panel Inspect keyboard and control panel. Note any damaged or missing items. Cables & Check all internal cable harnesses and connectors for wear and secure connector seating. Pay Connectors special attention to footswitch assembly and probe strain or bend reliefs. Shielding & Check to ensure that all EMI shielding, internal covers, air flow panels and screws are in place. Covers Missing covers and hardware could cause EMI/RFI problems while scanning. 6 External I/O Check all connectors for damage. 7 Op Panel Lights Check for proper operation of all operator panel and Freeze Key light. 10-8 Section 10-5 - System Maintenance

[Page 229] 10-5-6 Optional Diagnostic Checks Optionally you can access the diagnostic software as described in Chapter 5 or 7. View the error logs and run desired diagnostics. 10-5-6-1 View the Logs 1.) Review the system error log for any problems. 2.) Check the temperature log to see if there are any trends that could cause problems in the future. 3.) Check the Configuration Log; update if needed. 10-5-7 Probe Maintenance 10-5-7-1 Probe Related Checks Table 10-10 Probe Related Checks 1 Probe Holder Clean probe holders (they may need to be soaked to remove excess gel). Thoroughly check the system probe connectors and remove dust from inside the connector sockets 2 Probes if necessary. Visually check for bent, damaged or missing pins 10-5-7-2 Basic Probe Care The system user manuals and various probe handling cards provide a complete description of probe care, maintenance, cleaning and disinfection. Ensure that you are completely familiar with the proper care of GE probes. Ultrasound probes can be easily damaged by improper handling. See the User Manual and probe care cards for more details. Failure to follow these precautions can result in serious injury and equipment damage. Failure to properly handle or maintain a probe may also void its warranty. Any evidence of wear indicates the probe cannot be used. Do a visual check of the probe pins and system sockets before plugging in a probe. 10-5-7-3 Basic Probe Cleaning Refer to the User’s Manual for details on probe cleaning. NOTE: To help protect yourself from blood borne diseases, wear approved disposable gloves. These are made of nitrile derived from vegetable starch to prevent allergic latex reactions. NOTE: Failure to follow the prescribed cleaning or disinfection procedures will void the probe’s warranty. DO NOT soak or wipe the lens with any product not listed in the User Manual. Doing so could result in irreparable damage to the probe. Follow care instructions that came with the probe. NOTE: Disinfect a defective probe before you return it. Be sure to tag the probe as being disinfected. Chapter 10 Care & Maintenance 10-9

[Page 230] 10-5-8 Battery Performance Maintenance Battery replacement every three years is recommended. It is recommended to do battery performance maintenance one time per year. Please follow the flow chart below to carry out battery performance maintenance. Battery discharge No >45 minutes? Yes Battery charge > 3 hour Battery charge > 3 hour No No Battery power > 90%? Battery power > 90%? Yes Yes Replace battery Battery is Ok Discharge Replace battery No >45 minutes? Yes Battery is Ok Replace battery Figure 10-1 Flow chart of Battery Performance Maintenance NOTE: Disconnect all probes when discharge battery. NOTE: Discharge the battery to let the system automatically shut down. 10-10 Section 10-5 - System Maintenance

[Page 231] Section 10-6 Electrical Safety Tests 10-6-1 Safety Test Overview The electrical safety tests in this section are based on and conform to IEC 60601-1 Medical Equipment Safety Standards. They are intended for the electrical safety evaluation of cord-connected, electrically operated, patient care equipment. If additional information is needed, refer to the IEC 60601-1 documents. WARNING WARNING THE USER MUST ENSURE THAT THE SAFETY INSPECTIONS ARE PERFORMED AT LEAST EVERY 6 MONTHS ACCORDING TO THE REQUIREMENTS OF THE PATIENT SAFETY STANDARD IEC-EN 60601-1. ONLY TRAINED PERSONS ARE ALLOWED TO PERFORM THE SAFETY INSPECTIONS MENTIONED ABOVE. CAUTION To avoid electrical shock, the unit under test must not be connected to other electrical equipment. The unit under test must not be contacted by users or patients while performing these tests. CAUTION Possible risk of infection. Do not handle soiled or contaminated probes and other components that have been in patient contact. Follow appropriate cleaning and disinfecting procedures before handling the equipment. Test the system, peripherals and probes for leakage current. Excessive leakage current can cause injury or death in sensitive patients. High leakage current can also indicate degradation of insulation and a potential for electrical failure. Do not use probes or equipment having excessive leakage current. To minimize the risk that a probe may shock someone the customer should: • Not use a probe that is cracked or damaged in any way • Check probe leakage current: * Based on your facilities QA program for surface probes * Based on your facilities QA program for endocavitary probes * whenever probe damage is suspected Chapter 10 Care & Maintenance 10-11

[Page 232] 10-6-2 GEMS Leakage Current Limits The following limits are summarized for IEC 60601-1 Medical Equipment Safety Standards. These limits are GEMS standards and in some cases are lower than the above standards listed. Table 10-11 Chassis Leakage Current Limits—Accessible Metal Surfaces Country Normal Condition Open Ground Reverse Polarity Open Neutral All (Except USA & 0.1 mA 0.5 mA 0.5 mA 0.5 mA Canada) USA & Canada 0.1 mA 0.3 mA 0.3 mA 0.3 mA Table 10-12 Type BF Applied Part Leakage Current Limits - Probes surface Normal Country Condition Open Ground Reverse Polarity Open Neutral *Mains Applied All 0.1 mA 0.5 mA 0.5 mA 0.5 mA 5.0 mA Table 10-13 Type CF Applied Part Leakage Current Limits - ECG Connections Country Normal Condition Open Ground Reverse Polarity Open Neutral *Mains Applied All 0.01 mA 0.05 mA 0.05 mA 0.05 mA 0.05 mA NOTE: *Mains Applied refers to the sink leakage test where mains (supply) voltage is applied to the part to determine the amount of current that will pass (or sink) to ground if a patient contacted mains voltage. The following tests are performed at the factory and should be performed at the site. These tests are: chassis leakage current, and probe leakage current. All measurements are made with an electrical safety analyzer which should be calibrated and compliant with AAMI/ESI 1993 or IEC 60601 or AS/NZS 3551. 10-12 Section 10-6 - Electrical Safety Tests

[Page 233] 10-6-3 Outlet Test - Wiring Arrangement Test all outlets in the area for proper grounding and wiring arrangement by plugging in the neon outlet tester and noting the combination of lights that are illuminated. Any problems found should be reported to the hospital immediately and the receptacle should not be used. Figure 10-2 Typical Alternate Outlet Tester NOTE: No outlet tester can detect the condition where the Neutral (grounded supply) conductor and the Grounding (protective earth) conductor are reversed. If later tests indicate high leakage currents, this should be suspected as a possible cause and the outlet wiring should be visually inspected. Chapter 10 Care & Maintenance 10-13

[Page 234] 10-6-4 Chassis Leakage Current Test 10-6-4-1 Definition This test measures the current that would flow in a grounded person who touched accessible metal parts of the bedside station if the ground wire should break. The test verifies the isolation of the power line from the chassis. The meter is connected from accessible metal parts of the case to ground. Measurements should be made with the unit On and Off, with the power line polarity Normal and Reversed. Record the highest reading. CAUTION Electric Shock Hazard. When the meter's ground switch is OPEN, don't touch the unit! CAUTION Equipment damage possibility. Never switch the Polarity and the status of Neutral when the unit is powered ON. Be sure to turn the unit power OFF before switching them using the POLARITY switch and/or the NEUTRAL switch. Otherwise, the unit may be damaged. 10-6-4-2 Generic Procedure The test verifies the isolation of the power line from the chassis. The testing meter is connected from accessible metal parts of the case to ground. Measurements should be made with the unit ON and OFF, with the power line polarity Normal and Reversed. Record the highest reading of current. Figure 10-3 Set Up for Chassis Source Leakage Current, IEC 601-1 Clause 19 - Continuos Leakage Currents and Patient, Auxiliary Currents When using the Microguard or a similar test instrument, its power plug may be inserted into the wall outlet and the equipment under test is plugged into the receptacle on the panel of the meter. This places the meter in the grounding conductor and the current flowing from the case to ground will be indicated in any of the current ranges. The maximum allowable limit for chassis source leakage is shown in Table 10-11. 10-14 Section 10-6 - Electrical Safety Tests

[Page 235] 10-6-4-3 Data Sheet for enclosure Source Leakage Current The test passes when all readings measure less than the value shown in Table 10-11. Record all data on the PM Inspection Certificate. Table 10-14 Typical Data Sheet for enclosure Source Leakage Current Test 2 Tester Neutral Test 1 Real Panel Tester Polarity or Ground Speaker Metal Optional Optional Unit Power Switch Switch Cover Parts Test 3 Test 4 Enter Name of tested peripheral here: ON NORM OPEN ON NORM CLOSED ON REV OPEN ON REV CLOSED OFF NORM OPEN OFF NORM CLOSED OFF REV OPEN OFF REV CLOSED Chapter 10 Care & Maintenance 10-15

[Page 236] 10-6-5 Probe Leakage Current Test 10-6-5-1 Definition This test measures the current that would flow to ground from any of the probes through a patient who is being scanned and becomes grounded by touching some other grounded surface. 10-6-5-2 Generic Procedure Measurements should be made with the ground open and closed, with power line polarity normal and reversed, and with the unit Off and On. For each combination, the probe must be active to find the worst case condition. POLARITY REVERSING SWITCH H (BLACK) PROBE CONSOLE N (WHITE) POWER OUTLET G (GREEN) MOMENTARY SWITCH LEAKAGE TEST METER Figure 10-4 Set Up for Probe Leakage Current NOTE: Each probe will have some amount of leakage current, dependent on its design. Small variations in probe leakage currents are normal from probe to probe. Other variations will result from differences in line voltage and test lead placement. 10-6-5-3 No Meter Probe Adapter Procedure Follow the Safety Analyzer tool instruction to test each transducer for leakage current. The electrical Safety Analyzer tool should be calibrated and compliant with AAM/ESI 1993 or IEC 60601 or AS/NZS 3551. 10-16 Section 10-6 - Electrical Safety Tests

[Page 237] 10-6-5-4 Data Sheet for Transducer Source Leakage Current The test passes when all readings measure less than the values shown in Table 10-11. Record all data on the PM Inspection Certificate. Equipment damage possibility. Never switch the Polarity and the status of Neutral when the unit CAUTION is powered ON. Be sure to turn the unit power OFF before switching them using the POLARITY switch and/or the NEUTRAL switch. Otherwise, the unit may be damaged Table 10-15 Typical Data Sheet For Transducer Source Leakage Current Transducer Tested: Tester Power Polarity Tester GROUND or Unit Power Switch NUETRAL Switch Measurement ON NORM OPEN ON NORM CLOSED ON REV OPEN ON REV CLOSED OFF NORM OPEN OFF NORM CLOSED OFF REV OPEN OFF REV CLOSED Chapter 10 Care & Maintenance 10-17

[Page 238] Section 10-7 When There's Too Much Leakage Current... AC/DC FAILS Check any broken of the AC/DC adapter and its cable. Replace a new one if any portion defective. ENCLOSURE FAILS Check any broken of the enclosure. Replace any defective part. Inspect wiring for bad crimps, poor connections, or damage. Test the wall outlet; verify it is grounded and is free of other wiring abnormalities. Notify the user or owner to correct any deviations. As a work around, check the other outlets to see if they could be used instead. NOTE: No outlet tester can detect the condition where the white neutral wire and the green grounding wire are reversed. If later tests indicate high leakage currents, this should be suspected as a possible cause and the outlet wiring should be visually inspected. PROBE FAILS Change another probe to confirm if the fail is caused by console. NOTE: Each probe will have some amount of leakage, dependent on its design. Small variations in probe leakage currents are normal from probe to probe. Other variations will result from differences in line voltage and test lead placement. The maximum allowable leakage current for body surface contact probe differs from inter-cavity probe. Be sure to enter the correct probe type in the appropriate space on the check list. If excessive leakage current is slot dependent, inspect the system connector for bent pins, poor connections, and ground continuity. If the problem remains with the probe, replace the probe. PERIPHERAL FAILS Inspect wiring for bad crimps, poor connections, or damage. STILL FAILS If all else fails, begin isolation by removing the probes, external peripherals, then the on board ones, one at a time while monitoring the leakage current measurement. NEW UNIT If the leakage current measurement tests fail on a new unit and if situation can not be corrected, submit a Safety Failure Report to document the system problem. Remove unit from operation. 10-18 Section 10-7 - When There's Too Much Leakage Current...

[Page 239] ULTRASOUND INSPECTION CERTIFICATE Customer Name: System ID: Dispatch Number / Date Performed: Warranty/Contract/HBS System Type Model Number: Serial Number: Manufacture Date: Probe 1: Frequency: Scan Format*: Model Number: Serial Number: Probe 2: Frequency: Scan Format*: Model Number: Serial Number: Probe 3: Frequency: Scan Format*: Model Number: Serial Number: Probe 4: Frequency: Scan Format*: Model Number: Serial Number: Probe 5: Frequency: Scan Format*: Model Number: Serial Number: * Scan Format: Phased Array, Linear Array, Curved Array, Mechanical Array or Other FUNCTIONAL CHECKS PHYSICAL INSPECTION AND CLEANING OK? or Physical Inspection and Cleaning Functional Check (if applicable) N/A (if applicable) Inspect Clean B-Mode Function Console Doppler Modes Function LCD CF-Mode Function External I/O M-Mode Function Cables and Connectors Applicable Software Options GE Approved Peripherals (DVD-RW, Printer) Applicable Hardware Options Labeling (see User Manual for Labeling) Control Panel LCD Measurement Accuracy GE Approved Peripherals COMMENTS: ______________________________________________________________________________ ______________________________________________________________________________ Chapter 10 Care & Maintenance 10-19

[Page 240] ______________________________________________________________________________ ______________________________________________________________________________ ELECTRICAL SAFETY Max Value Value Electrical Test Performed Allowed Measured OK? Comments Outlet (correct ground &wiring config.) Type BF Applied Part Leakage Current Limits- Probe enclosure Source Leakage Current - Chassis Leakage Current Limits Peripheral 1 Leakage Current Peripheral 2 Leakage Current PROBES Probe Number Max Value Max Value (from previous page) Allowed Measured OK? Comments Probe 1: Probe 2: Probe 3: Final Check. All system covers are in place. System scans with all probes as expected. Accepted by: ______________________________________________________________________ 10-20 Section 10-7 - When There's Too Much Leakage Current...

[Page 241] This page was intentionally left blank. Chapter 10 Care & Maintenance 10-21

[Page 242] 10-22 Section 10-7 - When There's Too Much Leakage Current...

[Page 243] INDEX A,B EMI, 1-18 Abbreviations, 9-1 ESD, 1-18 Archiving Images Exam study Move, 4-31 display location, 4-9 Backup Patient Database, 4-28 Preset Configurations, 4-28 F Basic Measurements Focal zone Functional Checks, 4-25 display location, 4-9 Body pattern Functional Checks display location, 4-9 Basic Measurements, 4-25 Boot Up, 3-9 Control Panel, 4-7 Image Management, 4-27 Monitor Display, 4-9 C Peripherals, 4-37 Caps lock Probes/Connector Usage, 4-25 display location, 4-9 CE Compliance, 1-18 Cine gauge G display location, 4-9 Gathering Trouble Data, 7-2 Color Mode General Cleaning, 10-7 Overview, 4-20 Gray/color bar Configuration, 5-19 display location, 4-9 Connectivity Worksheet, 3-28 Contact Information, 1-19 Control Panel, 4-7 Hazard Icons, 1-6 Conventions Hospital name Conventions Used in Book, 1-5 display location, 4-9 Customer Assistance, 1-19 Human Safety, 1-11 CW Doppler activating, 4-24 exiting, 4-24 Image Management Functional Checks, 4-27 Image preview Dangerous Procedure Warnings, 1-16 display location, 4-9 Date/Time Imaging parameters display location, 4-9 display location, 4-9 Depth scale Inrush Current, 2-2, , 2-3 display location, 4-9 Institution name Diagnostics, 5-17 display location, 4-9 DICOM Network Function, 2-9 Logs, 5-14 Electrical LOTO, 1-16, , 4-6 requirements, 2-2 Electrical Safety, 1-12 Electrostatic Discharge Warning, 1-18 Index 1

[Page 244] M S Measurement summary window Safety Considerations, 1-11 display location, 4-9 Screen Captures, 7-6 Mechanical Safety, 1-11 System Maintenance, 10-5 Media System Manufacturer, 1-20 Formatting, 4-28 System messages Models Covered, 1-3 display location, 4-9 Monitor Display Functioanl Checks, 4-9 Monitor display T location, 4-9 TGC Move display location, 4-9 Archiving Images, 4-31 Touch Panel Functional Checks, 4-7 Trouble Image with Logs, 7-3 O Troubleshooting Operator identification Gathering Trouble Data, 7-2 display location, 4-9 Screen Captures, 7-6 Trouble Image with Logs, 7-3 Vital System Information, 7-2 P4 Key Function, 7-4, , 7-6 Patient identification U display location, 4-9 Utilities, 5-19 Patient name display location, 4-9 PC Diagnostics, 7-13 W Hard Drive Tests, 7-13 Warnings and Cautions, 1-11 Keyboard Test, 7-14 Memory Tests, 7-13 PC Diagnostics (Interactive Tests), 7-14 Peripherals Functional Checks, 4-37 Power On, 3-9 Power Requirements, 2-2 electrical, 2-2 stability, 2-3 Power Stability Requirements, 2-3 Probe Connector Cleaning, 10-9 Probe identifier display location, 4-9 Probe orientation marker display location, 4-9 Probes/Connector Usage Functional Checks, 4-25 Required Features, 2-7 Restore Patient Database, 4-30 Preset Configurations, 4-30 Index 2

[Page 245]

[Page 246] © 2004 to 2011, General Electric Company. GE Medical Systems, a General Electric Company, going to market as GE Healthcare. 3200 N. Grandview Boulevard Waukesha, Wisconsin 53149 USA www.gehealthcare.com